Guide

How to make a cut list for cabinets

Derive every carcass part of a 24 inch base cabinet from width, height and depth: formula, numbers and result per part, with rules C-5 to C-12 explained.

A cut list is every part of a cabinet with its quantity, length, width, thickness and grain direction. You make one by working from the three outside sizes inward: find the interior width (24 less two panel thicknesses is 22 9/16), then size each part from that. For a 24 face frame base the sides are 34 1/2 by 23 1/4, the bottom 22 9/16 by 23 and the back 23 5/16 by 30.

The table below shows the formula, the numbers and the result for every carcass part of that cabinet, with the rule ID the tool uses.

The derivation, part by part

This is one cabinet: 24 wide, 34 1/2 high, 24 deep including a 3/4 face frame, one drawer over one door, one shelf, a notch toe kick, and 23/32 panels with a 1/4 rabbeted back. Every number in the table comes from the same engine as the tool, so the table cannot drift from it.

Derivation of the carcass parts of a 24 x 34 1/2 x 24 face frame base. The formula column has your numbers substituted in.
PartQtyRuleFormula with numbersResult (L x W)
Side2C-5, C-6H_side x D_side = 34 1/2 x 23 1/4 (D_side = D - T_ff = 24 - 3/4 = 23 1/4)34 1/2 x 23 1/4
Bottom1C-8, C-9, C-10L_h x D_h = (W_in + 2j) x (D_side - rabbet) = (22 9/16 + 0) x (23 1/4 - 1/4) = 22 9/16 x 2322 9/16 x 23
Stretcher2C-11Stretcher = L_h x W_str = 22 9/16 x 422 9/16 x 4
Back, 1/41C-12Back = (W_in + 2 x d_rab) x H_box = (22 9/16 + 3/4) x 30 = 23 5/16 x 3023 5/16 x 30
Shelf1C-14Shelf = (W_in - shelf_gap) x (D_h - shelf_setback) = (22 9/16 - 1/8) x (23 - 1/4) = 22 7/16 x 22 3/422 7/16 x 22 3/4
Toe kick board1C-16Kick board = W_box x kick_h = 24 x 4 1/224 x 4 1/2
Derivation of the carcass parts of a 24 x 34 1/2 x 24 face frame base. The formula column has your numbers substituted in.

These parts are the carcass. The frame, doors and drawer have their own rules, covered in face frames, doors and drawer boxes.

How to do it by hand, in order

  1. Write down the cabinet width, height and depth, and which style you are building. Decide the settings: panel thickness, back thickness, back method, joint, toe kick size.
  2. Measure the sheet you will actually use. Enter its real thickness, not the nominal one.
  3. Work out the box: width 24 (C-1), height above the kick 30 (C-4) and the interior width 22 9/16 (C-7).
  4. Size the sides, then the horizontals from the interior width, then the back, shelf and kick.
  5. Add the frame, doors and drawer parts, if the cabinet has them.
  6. List grain direction against each part and any edges to band, then group the parts by material and thickness for the sheet layout.

The rules in plain words, with one number each

The sizing rules for the carcass, with the 24 inch base as the worked number.
RuleIn plain wordsWorked number
C-5 side depthCabinet depth, less the frame thickness if the depth includes the frame, less the back thickness if the back is applied.24 - 3/4 = 23 1/4
C-6 sidesTwo, the full height with a notch for the kick, or the height less the kick for a separate base.34 1/2 x 23 1/4
C-7 interior widthBox width less a panel thickness each side.24 - 1 7/16 = 22 9/16
C-8 horizontal lengthThe interior width, plus two dado depths if the joint is a dado.22 9/16 + 0 = 22 9/16
C-9 horizontal depthSide depth, less the back thickness if the back sits in a rabbet.23 1/4 - 1/4 = 23
C-10 bottomOne panel of the horizontal length and depth.22 9/16 x 23
C-11 topA base gets two stretchers; a wall or tall cabinet gets a full panel.2 at 22 9/16 x 4
C-12 backRabbeted: interior width plus a rabbet each side. Applied: the full box width. Height is the box height.22 9/16 + 3/4 = 23 5/16
The sizing rules for the carcass, with the 24 inch base as the worked number.
C-12

Back = (W_in + 2 x d_rab) x H_box = (22 9/16 + 3/4) x 30 = 23 5/16 x 30

The shelf comes next (C-14): the interior width less 1/8 for fit, by the horizontal depth less 1/4, which gives 22 7/16 by 22 3/4. The kick board (C-16) is the box width by the kick height, 24 by 4 1/2. The base cabinet box guide shows how each joint choice changes these.

Common mistakes

  • Nominal thickness. Entering 3/4 for a 23/32 sheet makes the interior 1/16 too narrow and the bottom 22 1/2 instead of 22 9/16.
  • Forgetting the back rabbet. A back cut to the interior width, 22 9/16, falls through the opening. It should be 23 5/16.
  • Using the cabinet depth as the side depth. On a face frame the sides are 23 1/4, and with an applied back they are 23.
  • Ignoring grain. Sides run with the grain along the height, horizontals along their length. A part rotated on the sheet can break that, and the layout should not rotate a grained part.
  • Mixing material thicknesses in one sheet count. The back is 1/4, so it goes on its own sheet group, apart from the 23/32 parts.

After the list comes the sheet count: see how many sheets for a kitchen and sheet layout and kerf. The build sequence is in how to build cabinets.

Questions people ask

What is a cut list?

A cut list is the list of every part you need to cut for a cabinet or a project, with quantity, length, width, thickness and grain direction. A cutting list for kitchen cabinets adds the parts for each cabinet and groups them by material.

What does a cutting list for kitchen cabinets contain?

For each cabinet it lists sides, bottom, stretchers or top, back, shelves and toe kick, plus the face frame, doors and drawer parts where they apply. Totals are then grouped by material and thickness so you can count sheets.

How do I calculate cabinet size for each part?

Start with the interior width, the box width less two panel thicknesses. The horizontal parts run that length, the side depth sets their depth, and the back, shelf and kick follow from those. Rules C-5 to C-12 give each formula.

What is the formula for cabinet side, bottom and back sizes?

The side is the cabinet height by the depth less the frame thickness. The bottom is the interior width by the side depth less the back thickness. A rabbeted back is the interior width plus two rabbet widths by the box height.

Why does thickness matter in a cut list?

Every horizontal part is cut to the interior width, which is the cabinet width less two panel thicknesses. A sheet sold as 3/4 inch usually measures a little less, so measure it and enter the real figure.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool