Sheet layout and saw kerf, explained
How a plywood cutting diagram works, how saw kerf and grain change the sheet count, and how to read each sheet. Worked on a real six-cabinet kitchen run.
A sheet layout places every part on a 4 by 8 sheet so that each cut runs edge to edge, and it leaves one saw kerf of space between neighbours. Kerf is the width of wood the blade turns to dust, 1/8 inch for a common blade, so a plan that ignores it puts parts too close to cut apart.
Kerf rarely changes the sheet count by itself. The one-kitchen sample below needs 5 sheets of 23/32 plywood at every kerf from 0 to 1/4 inch, and three kitchens' worth of the same cabinets needs 14 at 1/8 inch and 15 at 1/4 inch. What kerf protects is whether the layout can be cut at all.
What the layout is solving
The cut list gives you parts: a length, a width, a thickness and a grain direction. The layout puts those parts on identical stock sheets and counts how many sheets that takes. Parts are grouped by material and real thickness first, because a 1/4 inch back never shares a sheet with a 23/32 inch side. This run has 52 parts in its main plywood group, and the diagram shows the first sheet.
Every cut in the diagram is a guillotine cut: it runs from one edge of the piece you are cutting to the other, as it does on a table saw, a track saw or a panel saw. That is the only kind of cut the packer uses, so you can follow the layout without a CNC nesting machine. The method places each part in the free rectangle where it fits tightest, splits what is left over, and tries eight combinations of sort order and split rule. It keeps the one with the fewest sheets. This is a heuristic. A better arrangement may exist, so the product never calls its result optimal.
How kerf is counted
part_packed = (length + kerf) x (width + kerf); sheet_packed = (sheet_L - 2 x trim + kerf) x (sheet_W - 2 x trim + kerf)
Adding one kerf to every part and one to the sheet charges exactly one blade width between two neighbours and none against the sheet edge. A part at the edge of the sheet does not need a cut on its outer side, so the arithmetic gives it none. Trim, the waste you cut off each sheet edge before you start, comes off the sheet first (rule L-1).
| Kerf | One run: sheets | One run: yield | Three runs: sheets | Three runs: yield |
|---|---|---|---|---|
| 0 (not real) | 5 | 82% | 14 | 88% |
| 1/8 (default) | 5 | 82% | 14 | 88% |
| 1/4 | 5 | 82% | 15 | 82% |
The default of 1/8 inch (3.2 mm) is a planning figure for a common full-kerf blade. The real number for your blade is a test cut away: cut a scrap, measure the slot, and enter that. Thin-kerf blades remove less, and the saving shows up on a big job because every cut on every sheet gets a little wider or narrower.
Grain direction
Sheet grain runs along the 96 inch length. A part with a grain rule can only be placed with its grain parallel to that edge, so a 30 inch cabinet back with vertical grain lies across the sheet with its height along the 96. Parts in ungrained material, such as melamine or MDF, may turn 90 degrees, which usually saves a sheet. If a part is longer than the sheet allows in its permitted direction, the layout reports an error naming the part and the cabinet, and lays out the rest.
How to read the diagram
- Find the sheet count and yield above the diagram. Yield is part area over usable sheet area.
- Read each tape label as a part name. Identical parts are numbered, so two sides read Side 1 and Side 2.
- Follow the edge-to-edge lines. The longest lines are the first passes of the saw through the whole sheet.
- Cut each resulting piece along its own edge-to-edge lines until only single parts are left.
- Tick each part on the cut list as it comes off the sheet. The reference letters match the printed list and the part labels.
Common mistakes
- Laying out with kerf 0 because the count looks the same. The count may match, but the parts then touch edge to edge on the sheet and cannot be cut apart without losing a blade width each.
- Mixing 23/32 inch and 3/4 inch thicknesses in one list. They are different materials to the optimiser, as they should be.
- Forgetting trim. If you square each sheet edge first, set trim to the amount you remove.
- Ignoring a grain error and rotating the part by hand. The error is telling you the part does not fit the sheet the way the grain needs.
You can see every sheet of your own project for free in the tool. The layout is also the basis of the plywood calculator for cabinets, and the part sizes come from the face frame and frameless rules.
Count the sheets for your cabinets
Where the numbers on this page come from
Every number above was produced by the same engine and optimiser the product uses, run on a six-cabinet face frame kitchen run of 24 and 30 inch bases, an 18 inch drawer base, a 36 inch sink base and 30 and 24 inch wall cabinets, all at the product defaults. If the rules change, this page changes with them, and the build refuses to publish a sentence the engine no longer supports.
Questions people ask
What is saw kerf and how wide is it?
Kerf is the width of material the blade removes. A common table saw blade removes about 1/8 inch (3.2 mm); a thin-kerf blade removes less. Measure your own blade with a test cut and enter it as the kerf setting.
Does the layout include kerf at the sheet edge?
No. One kerf is charged between neighbouring parts and none against the sheet edge, because the outer edge of a sheet needs no cut. Trim is a separate setting for what you square off each edge.
Is the layout optimal?
No. It is a guillotine heuristic that tries eight combinations and keeps the best. A better arrangement may exist, so use the count as a planning number and keep an eye on what is left on the last sheet.