Guide

How to build cabinet doors

Cut sizes for a slab door and a five-piece shaker door from the engine: overlay and inset door size, stiles, rails, floating panel and build order.

A slab door is one panel cut to the opening plus the overlay each side: 21 wide opening, 1/2 overlay, 22 by 21 1/2 door. A five-piece door is the same overall size made from two stiles, two rails and a floating panel, which the engine sizes for you.

For the five-piece door in the same 22 by 21 1/2 size, the stiles are 2 1/4 by 21 1/2, the rails 18 1/4 by 2 1/4 and the panel 18 1/8 by 17 5/8. Raised-panel, arched and glass doors are not covered by this tool or this page.

Start with the door size

Whichever door you build, the overall size comes first. On a face frame cabinet with overlay doors, one door is the opening plus 1/2 on each edge (rule D-1), a pair with no centre stile is the opening plus both overlays less the gap between them, shared between the two (rule D-2), and an inset door is the opening less a 1/16 gap each edge (rule D-5). The numbers on this page use the 24 base with a drawer over one door.

Door sizes for the 24 inch face frame base and a 30 inch base with a pair, from the engine. The opening is 21 wide in the 24 inch cabinet.
CaseDoor (W x H)Rule
Single overlay door, 1/2 overlay22 x 21 1/2D-1
Single inset door, 1/16 gap20 7/8 x 20 3/8D-5
One of a pair on a 30 inch base13 15/16 x 28D-2
Door sizes for the 24 inch face frame base and a 30 inch base with a pair, from the engine. The opening is 21 wide in the 24 inch cabinet.
D-1

Door = (W_op + 2O) x (H_op + 2O) = (21 + 1) x (20 1/2 + 1) = 22 x 21 1/2

The overlay, inset and reveal choices and what they do to the sizes are in door overlay and reveal. The cabinet door size calculator does the same sums for any opening.

Track one: a slab door

A slab door is a single flat piece, so the part list is one line: 1 door, 22 by 21 1/2, 23/32 thick. Grain runs vertically on a door, along the height, so cut it with the grain along the 21 1/2 side. Cut it from plywood or MDF; the engine does not tell you which to use, it sizes the part. If you use plywood, band the four edges, since the engine marks all four edges of a slab door for banding (rule ER-1). The edge banding guide covers whether to take the banding off the cut size.

  1. Cut the door to 22 by 21 1/2 with the grain along the height.
  2. Check the size against the opening before you finish it: it should overlap the frame by 1/2 all round.
  3. Band the edges, sand, finish.
  4. Bore the hinge cups to the hinge maker's instructions and mount the door.

Track two: a five-piece door

A five-piece door keeps the same 22 by 21 1/2 overall size and builds it from a frame around a panel. The panel floats in a groove cut in the inside edge of the stiles and rails, 3/8 deep, with 1/16 of space at each edge so the panel can move. The stiles and rails are 2 1/4 wide by default.

The five-piece door for the same opening, with the product defaults.
PartQtyLengthWidthRule
Door stile22 1/421 1/2D-12
Door rail218 1/42 1/4D-13
Door panel118 1/817 5/8D-14
The five-piece door for the same opening, with the product defaults.
D-12

Stile = S_d x H_door = 2 1/4 x 21 1/2 (door 22 x 21 1/2 by D-1)

D-13

Rail = (W_door - 2 x S_d + 2 x g_d) x R_d = (22 - 4 1/2 + 3/4) x 2 1/4 = 18 1/4 x 2 1/4

D-14

Panel = (W_door - 2 x S_d + 2 x g_d - 2 x e_d) x (H_door - 2 x R_d + 2 x g_d - 2 x e_d) = 18 1/8 x 17 5/8

The stiles run the full height, and the rails run between them plus a groove depth at each end, which is the length of the stub tenon or the part of the rail that goes into the stile groove. The panel is as wide as the rail less the float on both sides. Because the numbers depend on the groove depth, rail width and float you pick, the five-piece door size guide shows how each setting moves them, and the shaker door calculator gives them for any door.

  1. Cut the stiles and rails to the list. Keep the stiles at full height and the rails at 18 1/4.
  2. Cut the groove for the panel, 3/8 deep, on the inside edge of all four frame parts.
  3. Cut the rail ends so they fit the stile groove (a stub tenon or a cope), then check a dry fit.
  4. Cut the panel to 18 1/8 by 17 5/8.
  5. Finish the panel before you glue up so that bare wood does not show when it shrinks.
  6. Glue the frame around the panel, with no glue on the panel itself, and clamp square.

Plywood or MDF

Either can make a slab door. A flat panel in a five-piece door is often plywood or MDF, and the frame parts are solid wood, so the engine lists the panel as a separate material of 1/4. We do not rank them, because the right choice depends on the finish and on what your suppliers stock. The decision that matters for the cut list is grain: plywood has it and MDF does not, and the tool can rotate an ungrained part when it lays out sheets.

Common mistakes

  • Sizing the door to the opening. An overlay door is bigger than the opening, by 1 in each direction here.
  • Gluing the panel into the frame. It must float; with 1/16 each edge it has room to move.
  • Cutting rails to the door width less the stiles. They also gain a groove depth at each end, so they are 18 1/4, not 17 1/2.
  • Forgetting that a pair is not two single doors. Each leaf of a pair is 13 15/16 wide here, because the gap between them is taken once.
  • Putting the grain across the door. Vertical grain along the height is the default.

The whole sequence is in how to build cabinets, and the drawer front that matches these doors is part of how to build drawer boxes.

Questions people ask

How do I make a slab cabinet door?

Cut one flat panel to the size of the frame opening plus the overlay on each edge, with the grain running along the height. Band or finish the edges, bore the hinge cups and hang it. The engine gives the size for any opening and overlay.

How do I make a shaker cabinet door?

A shaker door is a five-piece door with a flat panel: two stiles, two rails and a floating panel in a groove. Size the overall door first, then use the stile, rail and panel formulas (rules D-12 to D-14) or the shaker door calculator.

What size should I cut each part of a five-piece door?

Stiles run the full door height. Rails are the door width less two stile widths plus two groove depths. The panel is the rail length less float on each side, by the door height less two rails plus two grooves less float.

Can I make cabinet doors from plywood or MDF?

Yes, both are used for slab doors and for the floating panel in a five-piece door. The cut list sizes the part the same way; the difference is that plywood has grain and MDF does not, so grain direction matters only for plywood.

How big should the door be for my cabinet?

It depends on whether the door overlays or sits inside the frame. An overlay door is the opening plus the overlay on every edge, an inset door is the opening less a gap each edge, and a frameless door is the cabinet width less a small reveal each side.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool