Guide

How to build a face frame

Stile and rail sizes for a face frame from the engine, how pocket screws, dowels and tenons change rail length, centre stiles, overhang and assembly.

A face frame is two stiles that run the full height of the box and rails that run between them. For a 24 wide base the stiles are 1 1/2 by 30 (rule F-2) and each rail is 21 long (rule F-3), so the rails cover the width less one stile each side.

Join the rails to the stiles with pocket screws, dowels or tenons, glue the frame flat, then fix it to the front of the carcass. Only a tenon changes the rail length: it adds twice the tenon length, 1 1/2 at the default 3/4 tenon.

The parts of a 24 inch frame

The frame is 3/4 thick solid wood, not sheet goods. It is as wide as the cabinet (rule F-1) and as tall as the box above the toe kick, 30 here, because the frame runs from the top of the kick to the top of the cabinet. A drawer over a door needs three rails: top, middle and bottom.

Frame parts for the 24 x 34 1/2 face frame base with one drawer over one door and pocket joints.
PartQtyLengthWidthRule
Stile2301 1/2F-2
Top rail1211 1/2F-3, F-4
Middle rail1211 1/2F-3, F-4
Bottom rail1211 1/2F-3, F-4
Frame parts for the 24 x 34 1/2 face frame base with one drawer over one door and pocket joints.
Two stiles, a top rail, a middle rail and a bottom rail make the two openings that the drawer front and the door cover.
F-2

Stile = S_ff x H_ff = 1 1/2 x 30

F-3, F-4

Top rail = L_rail x width = (W_ff - 2 x S_ff + 2t) x 1 1/2 = (24 - 3 + 0) x 1 1/2 = 21 x 1 1/2

Grain runs along the length of every frame part, so a stile is cut from a board 30 or longer. The stiles are 1 1/2 wide and the rails 1 1/2, which are this tool's defaults rather than a standard. Make them wider if you want a heavier look, and the rails and the openings follow.

Joinery: how each choice changes the rail length

Rail length and width for the same frame with each joint. Stiles do not change.
JointRail (L x W)What it needs
Pocket screws21 x 1 1/2Pocket jig, glue, rail ends cut square
Dowels21 x 1 1/2Doweling jig, two or more dowels per joint
Tenons, 3/4 long22 1/2 x 1 1/2Tenon or mortise setup; the rail carries the tenon past the shoulder
Rail length and width for the same frame with each joint. Stiles do not change.

Pocket screws and dowels butt the rail end against the stile, so the rail is exactly the gap between stiles. A tenon is cut on the rail end and sits in a mortise in the stile, so the rail is longer by a tenon each end (rule F-3). Pockets are the default. They are quick, and the screws pull the joint tight while the glue sets. Dowels hide the joint on the face, and tenons give the most glue area. The engine treats the joint as a setting because either choice is valid.

Openings and the centre stile

With no centre stile the opening width is the frame width less two stiles: 21 on the 24 frame (rule F-5). That opening is what the door and drawer sizes start from, which is why the frame is worth building to size. See door overlay and reveal for the numbers that come from it.

A 36 base with a pair of doors and a centre stile has two openings of 15 3/4 each. The centre stile is 1 1/2 wide and 27 long, the height of the opening it divides (rule F-7), and each rail is 33 long (rule F-4). Fit the centre stile between the top and bottom rails when you assemble.

Assembly and attaching the frame

  1. Mill the stock to 3/4 thick and joint one edge. Cut the stiles 30 long and the rails 21 long for pockets or dowels.
  2. Mark every joint on the back face. Cut the pockets, drill the dowel holes or cut the tenons and mortises.
  3. Dry-fit the frame on a flat bench and check the diagonals. The two openings should each match the opening sizes in your cut list.
  4. Glue and clamp. Keep the clamps flat so the frame does not bow, and wipe squeeze-out off the inside edges while it is wet.
  5. Set the cabinet box face up. Spread glue on the front edges of the sides, bottom and stretchers, and lay the frame on. Line up the frame with the overhang you chose (see below).
  6. Fix the frame with brad nails or screws through the carcass edges, then clamp until the glue sets. Pocket holes in the stiles can screw into the box sides if you drill them from the inside.

Overhang past the box

The tool's default overhang is 0: the frame is flush with the sides of the box. Some shops leave a small overhang on the outside stile so it can be scribed to a wall, so the engine has an overhang setting. At 1/8 per side the box is 1/4 narrower than the frame (rule C-1), so the bottom is 22 5/16 long instead of 22 9/16. Frame stiles do not change. If you add overhang, check that the stile width is still more than the side thickness plus the overhang, or the engine reports that the carcass side stands proud of the frame opening (rule F-8).

Common mistakes

  • Cutting the rails to the full width. A rail is the width less two stiles, 21 here, not 24.
  • Adding the tenon length when the joint is pockets or dowels, or forgetting it when the joint is a tenon. The difference is 1 1/2 per rail.
  • Making the frame the height of the whole cabinet. It stops at the top of the toe kick, so it is 30, not 34 1/2.
  • Gluing the frame up out of square. A frame that is out by 1/16 shows as uneven reveals around every door.
  • Forgetting that cabinet depth includes the frame. The sides are 23 1/4 deep because the frame adds 3/4.

For the frame sizes of other cabinets, use the face frame calculator. The frame sits on the box described in how to build a base cabinet box, and face frame versus frameless compares the two lists. The whole sequence is in how to build cabinets.

Questions people ask

What do I need to cut for a cabinet face frame?

Two stiles that run the full height of the box above the toe kick, a top rail, a bottom rail, one middle rail for each divider between stacked openings, and a centre stile if a pair of doors is divided. All of them are cut from solid wood.

Do I use pocket screws, dowels or tenons for a face frame?

All three work. Pocket screws are quickest and are the tool default, dowels hide the joint on the face, and tenons give the most glue area. Only tenons change the rail length, which grows by two tenon lengths.

How long should the rails be?

For pocket screws or dowels a rail is the frame width less two stile widths, so 21 inches on a 24 inch frame with 1 1/2 inch stiles. With tenons add a tenon length at each end (rule F-3).

How do I attach a face frame to a cabinet box?

Glue the frame to the front edges of the sides, bottom and stretchers, line it up, then nail or screw it on and clamp until the glue sets. Check that the frame is flush with the sides, or has the overhang you planned.

How much should a face frame overhang the cabinet box?

The tool defaults to no overhang. Some shops leave a small overhang on an outside stile for scribing to a wall, so overhang is a setting. Each overhang makes the box narrower by the same amount, which shortens the horizontal parts.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool