Guide

How to build drawer boxes

Cut sizes for a cabinet drawer box from the opening: sides, front and back by joint, the grooved bottom, build order and common mistakes.

Size the box from the opening: with side-mount slides it is 1/2 narrower per side than the opening, so an 18 wide opening takes a 17 wide box. Cut two sides 22 long, two ends 16 long and one bottom 16 1/2 by 21 1/2, then glue the box and slide the bottom into its groove before the last end goes on.

The joint decides the end length (rule B-7) and the groove decides the bottom (rule B-8). The slide clearances themselves, and the undermount rules, are in drawer box sizes for side-mount and undermount slides.

The box for an 18 inch opening

The cabinet is 21 wide, so the face frame leaves an 18 opening. The drawer is one 5 high opening over a door, on side-mount slides, with 1/2 sides and a 1/4 bottom. These are the product defaults; every size changes if you change the setting.

Drawer box parts for an 18 inch opening, butt joints and side-mount slides.
PartQtyLengthWidthRule
Drawer side2224 1/4B-4, B-5, B-7
Drawer front/back2164 1/4B-3, B-7
Drawer bottom, 1/4116 1/221 1/2B-8
Drawer box parts for an 18 inch opening, butt joints and side-mount slides.
B-3, B-7

Front/back = (W_bx - 2 x T_ds) x H_bx = 16 x 4 1/4; W_bx = W_dop - 2 x c_side = 18 - 1 = 17

B-4, B-5

Side = L_slide x H_bx = 22 x 4 1/4; H_bx = H_dop - c_top - c_bot = 5 - 1/2 - 1/4 = 4 1/4

B-8

Bottom = (W_bx - 2 x T_ds + 2 x d_bg) x (L_bx - 2 x T_ds + 2 x d_bg) = 16 1/2 x 21 1/2

The side is as long as the slide, 22, because the box length is the slide length (rules B-5 and B-6). The slide is the longest standard length that fits the cabinet depth with 1 left behind it. The box height is the opening less the clearance above and below (rule B-4). Grain on the sides and ends runs along the length.

Butt, rabbet or dovetail

Side and front/back sizes for the same opening and each corner joint.
JointSide (L x H)Front and back (L x H)
Butt22 x 4 1/416 x 4 1/4
Rabbet, 1/4 deep22 x 4 1/416 1/2 x 4 1/4
Dovetail22 x 4 1/417 x 4 1/4
Side and front/back sizes for the same opening and each corner joint.

With a butt joint the ends sit between the sides, so each end is the box width less two side thicknesses. A rabbet in each end of the front and back lets the sides cover the ends and adds 1/4 per end, so the ends are 16 1/2. A through dovetail runs the ends the full box width, 17. The sides do not change. Dovetails are the strongest and the slowest, butt joints with glue and screws or brads are the quickest, and a rabbet is a middle road. The engine treats the joint as a setting because all three build a drawer.

The bottom groove

The bottom sits in a groove 1/4 deep cut in the inside face of the sides and ends. It is 16 1/2 by 21 1/2: the inside size of the box plus a groove each side (rule B-8). The groove must be shallower than the side, or it cuts through. Cut it before you assemble, about a bottom thickness from the lower edge, and slide the bottom in from the back while the box is still open.

The bottom is 1/4 here. A thicker bottom does not change its size, only the groove width, so you can use a different plywood and the same numbers.

Assembly

  1. Cut the sides and ends to the list and label them. Mark the inside face of each, because the groove goes on the inside.
  2. Cut the joints (rabbets or dovetails) if you are not using butt joints.
  3. Cut the bottom groove on the inside face of all four parts, 1/4 deep.
  4. Dry fit with the bottom in place. The box should measure 17 overall and 22 long.
  5. Glue the sides to the front and one end, drop the bottom in, then close the box with the last end.
  6. Check the diagonals before the glue sets, then fit the slides and attach the drawer front.

The drawer front is a separate part, 19 by 6, and it carries the face you see. Its size comes from the opening and the overlay, not from the box: see door overlay and reveal. For the box dimensions for other openings, use the drawer box calculator.

Common mistakes

  • Making the box the full opening width. Side-mount slides need 1/2 per side, so the box is 17 in an 18 opening.
  • Cutting the ends to the box width when the joint is a butt joint. They are 16, shorter by two side thicknesses.
  • Forgetting the groove when sizing the bottom. The bottom is 16 1/2 wide, not 16.
  • Using a slide as long as the cabinet is deep. The engine leaves 1 behind the slide, so a 24 inch deep cabinet takes a 22 slide here.
  • Making the box too shallow in height. The engine refuses a box under 2 inches high.

Next is the front on the box: how to build cabinet doors covers the door side. The whole job is in how to build cabinets.

Questions people ask

What size should I make a drawer box?

With side-mount slides the box is the opening width less 1/2 inch each side, and the height is the opening less the clearance above and below. The length is the longest standard slide that fits the cabinet depth. Undermount slides use different rules.

Should I use butt joints, rabbets or dovetails for a drawer box?

All three work. Butt joints are quickest, rabbets add glue area, and dovetails are the strongest. Only the length of the front and back changes with the joint, and the sides stay the same length.

How do I size the drawer bottom?

The bottom is the inside width of the box plus a groove depth each side, by the inside length plus a groove depth each end (rule B-8). It sits captured in a groove on all four sides.

How thick should drawer box plywood be?

The tool defaults to 1/2 inch sides and a 1/4 inch bottom. Undermount slides from Blum need sides no thicker than 16 mm. Thickness of the sides changes the front and back length, so enter what you use.

How do I fit the slides to the drawer box?

Slide fitting depends on the slide you buy, so follow the maker instructions. What the cut list controls is the clearance each side, the slide length and the box height, which are in the drawer box sizes guide.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool