Guide

How to build a base cabinet box

Build order, joinery choices and every part size for a 24 inch face frame base cabinet, with the formulas for sides, bottom, back, shelf and toe kick.

Cut the sides, bottom, stretchers and back to the list, join the sides to the bottom and stretchers, square the box with the back, then fix the face frame and the toe kick. The joinery you choose changes the numbers: a dado makes the bottom longer, and an applied back makes the sides shallower.

For a 24 inch face frame base with the product defaults, the sides are 34 1/2 by 23 1/4 and the bottom is 22 9/16 by 23. Every size below is produced by the engine, so you can change a setting and see which parts move.

The 24 inch face frame base, part by part

This is the cabinet the tool opens with: 24 wide, 34 1/2 high, 24 deep including the face frame, one 5 drawer over one door, one adjustable shelf, butt joints, a 1/4 back set in a rabbet and the notch toe kick. The panels are 23/32 plywood, the real thickness of most 3/4 inch sheets. With the drawer box and the frame it makes 20 pieces.

Every part of the 24 inch face frame base at the default settings. Lengths run with the grain.
PartQtyLengthWidthRule
Side234 1/223 1/4C-5, C-6
Bottom122 9/1623C-8, C-9, C-10
Stretcher222 9/164C-11
Back, 1/4123 5/1630C-12
Shelf122 7/1622 3/4C-14
Toe kick board1244 1/2C-16
Frame stile21 1/230F-2
Frame rail (top)1211 1/2F-3, F-4
Frame rail (middle)1211 1/2F-3, F-4
Frame rail (bottom)1211 1/2F-3, F-4
Drawer front (drawer 1)1226D-4
Drawer side (drawer 1)2224 1/4B-4, B-5, B-7
Drawer front/back (drawer 1)2194 1/4B-3, B-7
Drawer bottom, 1/4 (drawer 1)119 1/221 1/2B-8
Door (door 2)12221 1/2D-1
Every part of the 24 inch face frame base at the default settings. Lengths run with the grain.
The same cabinet pulled apart. Sides, bottom, stretchers, back, shelf and face frame are the parts in the table.
Front elevation: the frame stands on the box, and the drawer front and the door overlay the openings.

Assembly, in the order that keeps the box square

  1. Cut and label every part from the list. Mark the front edge of each side and of the bottom so a notch never ends up at the back.
  2. Cut the toe notch in each side: 4 1/2 high by 3 deep at the front bottom corner (rule C-6). Cut the dados or the back rabbet now if you are using them.
  3. Join the two sides to the bottom and to the two stretchers. On a butt joint that is glue and screws or fasteners through the sides into the panel ends.
  4. Square the box by its diagonals, then fix the back. A rabbeted back drops into its rabbet; an applied back is nailed and glued to the rear edges.
  5. Drop in the toe kick board, then set the face frame on the front. Pocket joints are the default frame joint (rule F-3).
  6. Fit the shelf last. It is cut 1/8 narrower than the interior and set back 1/4 from the front, so it slides in and clears the frame.

The formulas behind the table

The engine writes the formula, with your numbers, into each part. These are the ones that decide the box.

C-5

H_side x D_side = 34 1/2 x 23 1/4 (D_side = D - T_ff = 24 - 3/4 = 23 1/4)

C-8, C-9

L_h x D_h = (W_in + 2j) x (D_side - rabbet) = (22 9/16 + 0) x (23 1/4 - 1/4) = 22 9/16 x 23

C-12

Back = (W_in + 2 x d_rab) x H_box = (22 9/16 + 3/4) x 30 = 23 5/16 x 30

C-14

Shelf = (W_in - shelf_gap) x (D_h - shelf_setback) = (22 9/16 - 1/8) x (23 - 1/4) = 22 7/16 x 22 3/4

C-16

Kick board = W_box x kick_h = 24 x 4 1/2

Side depth (C-5) is the cabinet depth less the frame thickness when the depth includes the frame, and less the back thickness when the back is applied. Horizontal length (C-8) is the interior width, plus two dado depths if the joint is a dado. Horizontal depth (C-9) is the side depth less the back thickness when the back sits in a rabbet. Interior width is the box width minus two panel thicknesses (C-7). The face frame calculator covers the frame parts that sit on this box.

Joinery: how each choice moves the numbers

The same 24 inch face frame base with one setting changed at a time.
Setting changedSide depthBottom (L x W)Back (L x H)
Default: butt joint, rabbeted back23 1/422 9/16 x 2323 5/16 x 30
Dado joint, 1/4 deep23 1/423 1/16 x 2323 5/16 x 30
Applied back2322 9/16 x 2324 x 30
Panel thickness 3/423 1/422 1/2 x 2323 1/4 x 30
The same 24 inch face frame base with one setting changed at a time.

A butt joint is the quickest and the default. A dado locates the panel and resists racking, at the cost of an extra setup. The bottom has to be 1/2 longer to fill the dados, and the dado must be shallower than the panel, so the engine refuses a dado as deep as the panel. A rabbeted back sits inside the box and helps square it, so the back is larger than the interior by two rabbet widths. An applied back is the simplest to cut, and the sides lose the back thickness from their depth.

Settings that change the numbers

The settings that move the carcass sizes on this page, with their defaults.
SettingDefaultWhat it changes
T, panel thickness23/32Interior width, every horizontal length, the back size
T_back, back thickness1/4Back thickness; side depth if the back is applied
d_rab, back rabbet width3/8Back length; how far the back overlaps each side
d_dado, dado depth1/4Bottom and top length when the joint is a dado
T_ff, frame thickness3/4Side depth when the depth includes the frame
kick_h, kick_d4 1/2, 3Notch size, toe kick board height
shelf_gap, shelf_setback1/8, 1/4Shelf length and depth
The settings that move the carcass sizes on this page, with their defaults.

Common mistakes

  • Entering 3/4 inch for a 23/32 inch sheet. With 3/4 entered the bottom comes out 22 1/2, which is 1/16 short of a box built from 23/32 sheets. Measure the sheet and enter what you read.
  • Forgetting that the cabinet depth already includes the face frame. The sides are 23 1/4 deep, not 24, because the frame adds 3/4 at the front.
  • Cutting the back to the interior size when it sits in a rabbet. It must be 3/4 wider than the interior or it falls through.
  • Cutting the toe notch on the back corner. The notch is at the front bottom of each side, so mark a left and a right before you cut.
  • Gluing up before a dry fit. A box that is 1/16 out of square shows in the doors.

The next step is the fronts: see door overlay and reveal and drawer box sizes. If you are choosing between a frame and no frame, compare the two lists. Plywood for the whole job is counted in how many sheets for a kitchen, the toe kick options are in toe kick styles, and cut list in Excel or a tool shows how a wrong thickness spreads through a spreadsheet.

Questions people ask

What order should I assemble a base cabinet in?

Join the sides to the bottom and stretchers first, square the box by its diagonals, fix the back, then add the toe kick and the face frame. The shelf goes in last, and the doors and drawers after the finish.

Should I use a dado or a butt joint for the bottom?

A butt joint is faster and is the default. A dado locates the bottom and resists racking better, but it adds a cut and makes the bottom longer by two dado depths. Either is a valid choice, so the engine treats the joint as a setting.

Why is my cabinet side shallower than the cabinet depth?

On a face frame cabinet the stated depth includes the frame, so the side is the depth less the frame thickness. With an applied back the side also loses the back thickness. Rule C-5 is the formula.

How big should a rabbeted back be?

The back is the interior width plus a rabbet width on each side, by the box height above the toe kick (rule C-12). The rabbet must be shallower than the panel thickness, or the engine reports an error.

Does the plywood really measure 3/4 inch?

Most 3/4 inch plywood measures about 23/32 inch. Measure your sheet and enter the real thickness, because it feeds the interior width and every horizontal part length.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool