Guide

Cabinet door overlay and reveal, explained

How overlay, inset and frameless full overlay doors are sized, with worked single, pair and centre stile examples and the gap and reveal settings behind them.

Overlay doors lie on the face frame and are sized as the opening plus the overlay on every edge. Inset doors sit inside the opening and are the opening less a small gap on every edge. Frameless full overlay doors cover the whole box and are sized from the cabinet width and height less the reveals. For a 21 by 20 1/2 frame opening the overlay door is 22 x 21 1/2 and the inset door is 20 7/8 x 20 3/8.

Three ways to hang a door

Overlay: the door and drawer front lie over the frame, each covering part of the stile and rail.
Inset: the fronts sit inside the openings with a small gap all round.
Frameless full overlay: the fronts cover the box, separated by reveals.

In every case the rule starts from a different thing. Face frame work starts from the opening: the clear space between stiles and rails. Frameless work starts from the front zone: the box width less the side reveals and the box height less the top and bottom reveals. Both come from the same engine rules as the door size calculator.

Worked sizes

Door sizes for typical openings, from the engine at default settings. Face frame openings are 21 wide (24 inch cabinet) and 27 wide (30 inch cabinet), 20 1/2 high. Frameless cabinets are 24 and 30 wide with a 30 inch box.
CaseRuleEach door (W x H)Qty
Overlay, single doorD-122 x 21 1/21
Overlay, pair, no centre stileD-213 15/16 x 21 1/22
Overlay, pair with centre stileD-313 3/4 x 21 1/22
Inset, single doorD-520 7/8 x 20 3/81
Inset, pair, no centre stileD-613 13/32 x 20 3/82
Frameless, single doorD-1023 7/8 x 29 7/81
Frameless, pairD-1114 7/8 x 29 7/82
Door sizes for typical openings, from the engine at default settings. Face frame openings are 21 wide (24 inch cabinet) and 27 wide (30 inch cabinet), 20 1/2 high. Frameless cabinets are 24 and 30 wide with a 30 inch box.
D-1

Door = (W_op + 2O) x (H_op + 2O) = (21 + 1) x (20 1/2 + 1) = 22 x 21 1/2

D-2

Door = (W_op + 2O - G_pair) / 2 x (H_op + 2O) = (27 + 1 - 1/8) / 2 x (20 1/2 + 1) = 13 15/16 x 21 1/2

D-3

Door = (W_op + 2O) x (H_op + 2O), W_op = (W_ff - 2 x S_ff - M_ff) / 2 = 12 3/4; = 13 3/4 x 21 1/2

D-5

Door = (W_op - 2 x G_in) x (H_op - 2 x G_in) = (21 - 1/8) x (20 1/2 - 1/8) = 20 7/8 x 20 3/8

D-10

Door = W_fz x h = (24 - 1/8) x 29 7/8 = 23 7/8 x 29 7/8

D-11

Door = (W_fz - gap_pair) / 2 x h = (29 7/8 - 1/8) / 2 x 29 7/8 = 14 7/8 x 29 7/8 (W_fz = W - 2 x rev_side)

With a centre stile each door covers its own opening, and the centre stile itself is a frame part of width 1 1/2 (rule F-7). Without one the two leaves share one opening and a gap of 1/8 separates them, so they are narrower than half the opening plus overlay. Stacked fronts follow D-9: the heights plus the vertical gaps equal the front zone height.

The gap and reveal settings, and where the defaults come from

Door settings in the product and the source each default follows.
SettingDefaultSource
O, overlay per edge1/2inchcalculator.com: partial overlay often 1/2 inch
G_in, inset gap1/16inchcalculator.com: inset doors with a 1/16 inch gap
G_pair, face frame pair gap1/8WoodWeb: AWI nominal 3.2 mm between doors; the inchcalculator example uses 1/16, so it is a setting
rev_side, frameless side reveal1/16WoodWeb: 1.5 mm per side
gap_pair, frameless pair gap1/8WoodWeb: 3 mm between double doors
gap_v, gap between stacked fronts1/8WoodWeb: 3 mm to drawer fronts
rev_top, rev_bot1/8, 0WoodWeb: 3 mm at the top, 0 at the bottom
Door settings in the product and the source each default follows.

The metric defaults are 1.5 for the side reveal and 3 for the pair gap, and the imperial values are the nearest sixteenth or eighth. Sources are inchcalculator.com for the overlay and inset figures and the WoodWeb thread for the frameless reveals. WoodWeb is a forum thread, and its contributors differ: another uses 4 mm between double doors. That is why every figure is a setting and not a fixed rule.

Collisions: overlay against the middle rail

Two fronts that share a middle rail each overlap it. If twice the overlay is as wide as the rail, they touch or collide. The engine refuses it rather than printing sizes that cannot be built.

The same test applies to a centre stile: two doors overlap it by O each, so 2 x O must be less than the stile width (D-3). In all three cases the fix is a smaller overlay or a wider frame member.

Common mistakes

  • Measuring the whole cabinet width and adding the overlay. Overlay is added to the opening, which is the width between stiles, not to the cabinet width.
  • Sizing an inset door without the gap. Inset doors need the gap on every edge, or there is no room for the door to swing clear of the frame.
  • Using the cabinet height for a frameless door. The front zone starts above the toe kick, so it is the box height less the reveals (29 7/8 here).
  • Forgetting the gap in a pair. Each leaf is smaller than half the width by half the gap, which is why a pair is not simply the door width divided by two.
  • Letting the overlay run past the stile. Overlay may not be larger than the stile width (D-1).

Five-piece doors are cut from these sizes: see five-piece door sizes. For the drawer front and box that goes with the door, see drawer box sizes, and for how the two styles differ in full, face frame vs frameless. Door banding is covered in edge banding allowance and cut size.

Questions people ask

How do I calculate an overlay door size?

Measure the opening between the stiles and rails, then add the overlay on every edge. With the default overlay that is the opening width plus twice the overlay, and the opening height plus twice the overlay (rule D-1).

How big should the gap between two cabinet doors be?

The sources differ. WoodWeb gives 3 mm for frameless pairs and an AWI nominal 3.2 mm, and an inchcalculator example uses 1/16 inch. The product defaults to 1/8 inch and makes it a setting you can change.

What is a reveal on a frameless cabinet?

A reveal is the visible gap between a front and the cabinet edge. A frameless door is the cabinet width less a reveal at each side, and the height is reduced by the top and bottom reveals (rules D-8 and D-10).

Why does the engine refuse an overlay that looks fine?

Two fronts that share a middle rail each overlap it, so twice the overlay must be less than the rail width. If it is not, the doors would collide, and the engine reports an error and names the setting.

Do inset doors need a different opening?

No, the opening is the same. The inset door is the opening less the gap on each edge (rule D-5), so it is smaller than the opening, not larger.

Sources

  1. inchcalculator.com, Cabinet door calculator. Source S4 of the product rules Read .
  2. WoodWeb Knowledge Base, Frameless Cabinet Door Dimensions and Tolerances. Source S3 of the product rules Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool