Guide

Drawer box size for side-mount and undermount slides

Work a drawer box from one opening for side-mount slides and Blum TANDEM 563H undermount slides: width, height, length, bottom and the common mistakes.

A side-mount drawer box is the opening width less side space on each side, 1/2 inch with the default settings. An undermount box on Blum TANDEM 563H slides is the opening less 42 mm for the inside width, then the two side thicknesses added back. In the same 21 by 5 opening the side-mount box is 20 wide and the undermount box is 20 11/32 wide.

Box height and length change too. The side-mount box is 4 1/4 high on a 22 slide, and the undermount box is 4 3/16 high on a 21 slide.

The same opening, two slides

The opening is the one a 24 inch face frame base gives a drawer: 21 between the stiles, 5 high, 23 3/4 of clear depth from the front of the frame to the back of the cabinet. Box sizes come from the drawer box calculator in the product, which applies B-3 to B-8 to the opening you type. Joints are butt, sides are 1/2 and the bottom is 1/4.

Drawer box parts from one opening, side-mount against Blum TANDEM 563H undermount.
PartQtySide-mountUndermountRule
Box outside width12020 11/32B-3
Box height14 1/44 3/16B-4
Slide length22221B-5
Drawer side222 x 4 1/421 x 4 3/16B-7
Drawer front/back219 x 4 1/419 11/32 x 4 3/16B-7
Drawer bottom119 1/2 x 21 1/219 27/32 x 20 1/2B-8
Drawer box parts from one opening, side-mount against Blum TANDEM 563H undermount.
The same cabinet with undermount slides selected. The drawer box in the engine list matches the table above.

Formulas, with the numbers in

B-3 side-mount

W_bx = opening - 2 x c_side = 21 - 1 = 20

B-3 undermount

W_bx = opening - um_deduct + 2 x T_ds = 21 - 1 21/32 + 1 = 20 11/32

B-4 side-mount

H_bx = opening - c_top - c_bot = 5 - 1/2 - 1/4 = 4 1/4

B-4 undermount

H_bx = opening - c_top - c_bot = 5 - 1/4 - 9/16 = 4 3/16

B-5

Longest slide that is at most D_clear - c_rear = 23 3/4 - 1 = 22 3/4: 22

B-8

(W_bx - 2 x T_ds + 2 x d_bg) x (L_bx - 2 x T_ds + 2 x d_bg) = 19 27/32 x 20 1/2

B-1 and B-2 choose the opening: the frame opening on a face frame cabinet, or the interior width and the gap between fronts on a frameless one. B-6 makes the box as long as the slide. B-7 cuts the sides and the front and back, and with a butt joint the front and back sit between the sides. B-8 sizes a bottom captured in a groove on four sides.

What the sources support

The undermount figures follow the Blum TANDEM rules quoted by Popular Woodworking: an inside box width of the opening less 42 mm, at least 1/4 inch of clearance above the box sides and 9/16 inch below them, and a bottom recessed 1/2 so it clears the runner. The same rules limit side thickness to 16, so the engine accepts 1/2 sides and refuses thicker ones. The side-mount side space follows Accuride's guidance that slides may not function properly with less than 1/2 inch of side space. Treat both as the starting point and check the data sheet for the exact slide you buy; the engine says so in its note.

The undermount and side-mount defaults used above.
SettingSide-mountUndermount
Width ruleopening less 1opening less 42, plus 2 x 1/2
Clearance above / below the sides1/2 / 1/41/4 / 9/16
Nominal slide lengths10 to 289 to 30
Clearance behind the slide11
Largest side thicknessnot limited16
The undermount and side-mount defaults used above.

Slide lengths and the rear clearance are product defaults, not figures from those two pages, so change them to suit the slide you use.

Common mistakes

  • Picking the slide from the cabinet depth. The slide must be at most the clear depth less 1 of rear clearance. Here that is 22 3/4, so the longest side-mount slide is 22, not the cabinet's nominal 24. If nothing fits, the engine says so: No slide fits: 9 of depth minus 1 rear clearance leaves 8, and the shortest slide is 10.
  • Short side space. Cutting the box so the side space is under 1/2 inch each side. With 7/16 the engine warns: Side-mount slides may not work with less than 1/2 in (12.7 mm) of side space (source S2).
  • Thick undermount sides. The engine refuses 3/4 sides on this slide: Undermount drawer sides can be at most 5/8 thick (source S1, Blum). Yours are 3/4.
  • Using the wrong box height. Undermount needs more room below the sides than side-mount does, so a box height from one slide type is wrong for the other.
  • Forgetting the recessed bottom. An undermount bottom sits 1/2 up from the lower edge of the sides. It is a note on the list, not a size.

Door and drawer front sizes are a separate calculation: door overlay and reveal covers them. To size your own box, use the drawer box calculator.

Questions people ask

How do I size a drawer box for side-mount slides?

Take the opening width and subtract the side space on each side, which is 1/2 inch with the default settings. Height is the opening less the clearance above and below. Length is the longest slide that fits the clear depth less the rear clearance.

What is the 42 mm rule for Blum TANDEM undermount drawers?

The inside width of the drawer box is the opening width less 42 mm, as quoted by Popular Woodworking for the Blum TANDEM 563H. The outside width is that inside width plus the two side thicknesses. The engine applies it as rule B-3.

How thick can undermount drawer sides be?

The product rule limits sides to 16 mm for these slides, from the Blum figure quoted by Popular Woodworking. Half inch plywood is accepted. Anything over that is refused with an error that names the setting to change.

How much clearance does an undermount box need above and below?

The rules used here are 1/4 inch above the sides and 9/16 inch below them, with the bottom recessed 1/2 inch so it clears the runner. Check the data sheet for your slide.

Why is my slide shorter than the cabinet depth?

The slide has to fit the clear depth less the rear clearance, and slides come in fixed lengths. The engine takes the longest nominal length that fits, so a 24 inch deep cabinet takes a slide shorter than 24 inches.

Sources

  1. Accuride Europe, Understanding side space. Source S2 of the product rules Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool