Guide

Five-piece door sizes: stiles, rails and panels

How to size the stiles, rails and floating panel of a five-piece cabinet door, with the groove depth and panel gap, worked on a real door from the engine.

A five-piece door is two stiles, two rails and a floating panel. Stiles run the full height of the door, rails run between the stiles plus the groove depth at each end, and the panel is the rail length less the float. For a 22 by 21 1/2 door with 2 1/4 stiles and rails, a 3/8 groove and a 1/16 float, the stiles are 2 1/4 by 21 1/2, the rails are 18 1/4 by 2 1/4 and the panel is 18 1/8 by 17 5/8.

One door, worked through the engine

The door is the one on a 24 inch face frame base: an overlay door for a 21 wide opening, so 22 by 21 1/2 as a slab door (rule D-1). Switching the door type to five-piece does not change that finished size. It breaks the same size into frame parts and a panel, using stile and rail width 2 1/4, groove depth 3/8 and panel gap 1/16. The formula is the one on inchcalculator.com: rail length is the door width less two stile widths plus two groove depths, and its worked example uses these same defaults.

Five-piece door parts for the 24 inch base door, default settings.
PartQtyLengthWidthThicknessRule
Stile22 1/421 1/223/32D-12
Rail218 1/42 1/423/32D-13
Panel118 1/817 5/81/4D-14
Five-piece door parts for the 24 inch base door, default settings.
The 24 inch base with the door type set to five-piece. The door parts appear in the engine list as stiles, rails and a panel.
D-12

Stile = S_d x H_door = 2 1/4 x 21 1/2 (door 22 x 21 1/2 by D-1)

D-13

Rail = (W_door - 2 x S_d + 2 x g_d) x R_d = (22 - 4 1/2 + 3/4) x 2 1/4 = 18 1/4 x 2 1/4

D-14

Panel = (W_door - 2 x S_d + 2 x g_d - 2 x e_d) x (H_door - 2 x R_d + 2 x g_d - 2 x e_d) = 18 1/8 x 17 5/8

The stile is 23/32 thick like a slab door, and the panel is 1/4 sheet stock that floats in a groove. That is why the panel carries its own material and thickness in a cut list, and why it lands in a different sheet group from the frame parts.

The groove, the stub tenon and the float

The groove depth is the same number as the stub tenon length: each rail has a stub tenon as long as the groove is deep, which fits into the groove in the stile. That is why the rail is longer than the space between the stiles by two groove depths. The panel also goes into the groove, but it does not touch the bottom. The gap per edge, 1/16 here, lets the panel move with the seasons without pressing on the frame. Panel width and height both lose twice that gap. The panel goes into the groove by 5/16 on every edge.

How the settings move the panel and the rail on the same door.
ChangeRail lengthPanel (W x H)
Default18 1/418 1/8 x 17 5/8
Groove depth 1/218 1/218 3/8 x 17 7/8
Panel gap 1/818 1/418 x 17 1/2
Stile and rail 2 1/217 3/417 5/8 x 17 1/8
How the settings move the panel and the rail on the same door.

A wider stile and rail leave less panel. A deeper groove makes both the rail and the panel longer. The panel gap does not touch the rail, only the panel. Check every one against your router bits: a groove cut with a 1/4 cutter is only as deep as you set it, so enter the depth you actually cut.

A second door: a pair on a wall cabinet

Wide cabinets take a pair. The five-piece rules then apply to each leaf, so the part counts double. The example is a 30 inch wide, 30 inch high wall cabinet with a pair of overlay doors and the same stile, rail and groove settings.

Five-piece parts for a pair of doors on a 30 inch wall cabinet, default settings.
PartQtyLengthWidthRule
Door stile42 1/428D-12
Door rail410 3/162 1/4D-13
Door panel210 1/1624 1/8D-14
Five-piece parts for a pair of doors on a 30 inch wall cabinet, default settings.

Each leaf is 13 15/16 wide by 28 high before it is broken into parts, and the pair is two leaves with a 1/8 gap between them (rule D-2). The panels are narrower than the single door panel because the leaf is narrower. The stile and rail widths stay the same on every door in the cabinet.

Common mistakes

  • Cutting the rail to the space between the stiles. That leaves no tenon, so the rail is 3/4 too short.
  • Cutting the panel to the groove-to-groove size with no float. The engine takes 1/8 off each direction. With no gap, the panel cannot move.
  • Using the door finish size for the panel. The panel is 3 7/8 narrower than the door and 3 7/8 shorter, because it sits inside the frame.
  • Entering the stile width where the rail width goes. Stiles and rails are separate settings, even though both default to 2 1/4.
  • Gluing the panel in the groove. The panel has to float, so keep glue out of the groove.

The overall door size comes from the opening and the overlay: see door overlay and reveal. Panels are thin sheet, so they affect the sheet count in how many sheets for a kitchen. Banding on five-piece doors is covered in edge banding allowance and cut size.

Questions people ask

How long are the rails on a five-piece door?

Rail length is the door width less two stile widths plus two groove depths (rule D-13). The groove depth is added back because each rail has a stub tenon that fits into the groove in the stile.

How do I size the panel of a five-piece door?

The panel width is the rail length less two panel gaps, and the panel height is the door height less two rail widths, plus two groove depths, less two panel gaps (rule D-14). The panel gap lets the panel move.

How much should the panel float in the groove?

The product default is 1/16 inch per edge, from the worked example on inchcalculator.com. It is a setting. A panel in a wide door or a solid wood panel may need more, so enter the gap you want.

Are stiles longer than rails?

Yes. Stiles run the full height of the door. Rails run between the stiles, plus the groove depth at each end, so they are shorter than the door width.

What thickness is the panel?

The default panel is 1/4 inch sheet, the same stock as the cabinet back, while the frame is the door thickness. Both are settings, and the panel appears in its own material group on the cut list.

Sources

  1. inchcalculator.com, Cabinet door calculator. Source S4 of the product rules Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool