Guide

Edge banding allowance and cut size

Which edges get banded by style, how banding thickness changes cut size, and how much banding a kitchen needs with a waste allowance, from real engine runs.

Edge banding sits on top of the cut size. By default the cut list leaves the cut size equal to the finished size, and the banding thickness only matters if you turn on the setting that deducts it. With the deduction on, a banded edge is cut short by one banding thickness, 0.5 at the default, so a frameless door banded on four edges is 1 smaller each way in the saw.

For a six-cabinet frameless kitchen run the banding comes to 159.7 feet, and 175.6 feet with the 10% allowance.

Which edges get banded by default

Every part carries four edge flags: two along its length (L1, L2) and two across its width (W1, W2). On a side, the length is the height, so L1 is the front edge, the one you see when the door is open. The defaults depend on the style, and each class can be turned on or off in the settings.

Banded edges by part for the 24 inch base in each style, default settings. 'none' means unbanded.
PartFace frameFrameless
SidenoneL1
BottomnoneL1
Front stretchernoneL1
ShelfL1L1
Backnonenone
Drawer frontL1 L2 W1 W2L1 L2 W1 W2
DoorL1 L2 W1 W2L1 L2 W1 W2
Drawer box sidenonenone
Banded edges by part for the 24 inch base in each style, default settings. 'none' means unbanded.

On the face frame cabinet the frame covers the carcass front edges, so only the shelf front is banded. On the frameless cabinet the front edges of the sides, bottom and front stretcher show, so they are banded too. Doors and drawer fronts are banded on all four edges either way. See face frame vs frameless for the whole comparison.

Cut size and finished size

ER-2

cut_len = finished_len - T_eb x (banded short edges); cut_wid = finished_wid - T_eb x (banded long edges). With eb_deduct off, cut = finished.

Frameless 24 inch base, with and without the banding deduction. T_eb is 0.5. Millimetres to 0.1.
PartFinished (L x W)Cut, deduct offCut, deduct on
Door (L1 L2 W1 W2)606.4 x 603.2606.4 x 603.2605.4 x 602.2
Side (L1)762 x 609.6762 x 609.6762 x 609.1
Frameless 24 inch base, with and without the banding deduction. T_eb is 0.5. Millimetres to 0.1.

The door loses 0.5 from each edge it is banded on, so 1 in each direction. The side has one banded long edge, so it loses 0.5 from its width and nothing from its length. The finished size, door 23 7/8 wide, is what you measure after the banding goes on. The tool prints both columns when they differ. The default for the deduction is off, so cut size equals finished size. If you want the cut sizes to include it, turn it on.

The sheet layout uses the cut sizes, so the setting can move parts on the sheet. For the whole run it does not change the count here: 8 sheets either way.

PLYWOODToe kick boardFalse frontBottom34 9/16 x 23 3/4Rear stretcherFront stretcherSide 130 x 24Side 130 x 12Toe kick boardDoor23 11/16 x 29 13/16Bottom 128 9/16 x 11 3/4Toe kick boardDrawer frontRear stretcher
First sheet of the frameless run with the banding deduction on. The layout is packed from cut sizes.

Banding length with waste

ER-3

banding = sum over parts of qty x (banded edge lengths); total = banding x (1 + eb_waste)

Edge banding for the same six-cabinet run (24 and 30 inch bases, 18 inch drawer base, 36 inch sink base, 30 and 24 inch wall cabinets) in both styles.
StyleBanding (ft)With 10% waste (ft)
Face frame97.5107.2
Frameless159.7175.6
One frameless 24 inch base23.525.9
Edge banding for the same six-cabinet run (24 and 30 inch bases, 18 inch drawer base, 36 inch sink base, 30 and 24 inch wall cabinets) in both styles.

The waste allowance covers end trim, a short last roll and a miss. The 10% default is an assumption in the product, not a measured figure, so change it to what your edge bander and your hands actually waste. The length is reported per banding material. Buy banding by the foot or the roll above the total, not at it. For a cost estimate, the tool multiplies the total by the unit price you type. See pricing for the plans.

Common mistakes

  • Deducting the banding thickness by hand and again in the tool. Pick one place: either leave eb_deduct off and trim after banding, or turn it on and cut to the printed cut size.
  • Banding the carcass front on a face frame cabinet. It is covered by the frame, so the default leaves it bare. The face frame run needs 62.2 feet less banding than the frameless run.
  • Ordering banding to the exact total. Add the allowance so a miss or a short roll does not stop the job.
  • Forgetting which edge is L1. The tool and the CSV list the banded edges by flag, so you can match them to the part on the bench.
  • Banding thickness taken from a catalogue number you have not measured. Measure the roll and enter it as T_eb.

Doors are cut from the sizes in door overlay and reveal, and five-piece doors are banded as separate frame parts, so see five-piece door sizes. To count sheets with the cut sizes, use the plywood calculator, or read how many sheets a kitchen needs.

Questions people ask

Do I subtract edge banding thickness from the cut size?

Only if you want the cut size to be the size before banding. The product leaves the deduction off by default, so cut size equals finished size. Turn on eb_deduct and each banded edge is cut short by one banding thickness (rule ER-2).

How much edge banding do I need for a kitchen?

Add up the banded edge lengths of every part, then add a waste allowance. The product does this as rule ER-3 with a 10 percent default allowance, which is a planning assumption you can change. The example run above shows the totals for both styles.

Which edges are banded on a face frame cabinet?

By default only the shelf front and the four edges of doors and drawer fronts. The face frame covers the front edges of the sides, bottom and stretchers, so they are left bare.

Why does the frameless list need more banding?

A frameless cabinet has no frame in front of the carcass, so the front edges of the sides, bottom and front stretcher are visible and are banded by default. The run above puts a number on the difference.

Does the banding deduction change the number of sheets?

It can, because the layout packs from cut sizes, but the change is only 0.5 per banded edge. In the six-cabinet run above the sheet count is the same with it on or off.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool