Guide

Toe kick styles: notch, separate base and legs

Compare a notched toe kick, a separate base and levelling legs on the same 24 inch cabinet, with side heights, kick parts and cross member counts.

There are three ways to build the toe kick. A notch cuts a 4 1/2 by 3 step out of the front bottom of each full-height side. A separate base is a frame of rails and cross members under a shorter box. Legs put adjustable feet under a shorter box and add a kick board across the front.

For a 24 inch face frame base the notch side is 34 1/2 high, and the separate base and legs sides are 30 high. Only the separate base adds cross members, and the legs style adds 4 levelling legs.

The same cabinet three ways

The cabinet is the usual 24 wide, 34 1/2 high and 24 deep face frame base with a drawer, a door and a shelf. Only the kick style changes. The kick height (4 1/2) and kick depth (3) are settings, and the next section says where they come from.

The 24 inch face frame base with each toe kick style, default settings.
ItemNotchSeparate baseLegs
Side height x depth34 1/2 x 23 1/430 x 23 1/430 x 23 1/4
Notch on each side4 1/2 x 3nonenone
Kick parts1 x toe kick board 24 x 4 1/22 x base front/back rail 24 x 4 1/2; 2 x base cross member 18 13/16 x 4 1/21 x toe kick board 24 x 4 1/2
Levelling legs004
Total parts on the list202320
The 24 inch face frame base with each toe kick style, default settings.
Separate base: the box sits on a base frame of front and back rails with cross members between them.
Notch: full-height sides with the toe space cut out of the front bottom corner.
C-3

H_side = H when notch or wall; H - kick when separate base or legs. Here 34 1/2 or 30.

C-16

Cross member = (D_side - kick_d - 2T) x kick_h = (23 1/4 - 3 - 1 7/16) x 4 1/2 = 18 13/16 x 4 1/2

Each style also changes what the rest of the list does. The box height above the kick (C-4) is the same in all three, so the frame, back and doors do not change. Face frame height is the box height, so the frame sits on top of the kick in every case.

Cross members on a separate base

C-16

n_x = max(2, ceil(W_box / 24 in) + 1); each (D_side - kick_d - 2T) x kick_h

The base has a front rail and a back rail the width of the box, and cross members between them. Each cross member is the side depth less the kick depth and two panel thicknesses long. The count rule is a product assumption, not a figure from a source, so you can add members by hand if your base needs more.

Separate base parts by cabinet width, 24 inch deep face frame base.
Cabinet widthRail length (2 rails)Cross membersCross member length
18 in18218 13/16
24 in24218 13/16
30 in30318 13/16
36 in36318 13/16
48 in48318 13/16
Separate base parts by cabinet width, 24 inch deep face frame base.

Legs

With legs the sides stop at the foot of the box and four adjustable legs carry it. The kick board then fixes to the legs across the front. Extra legs are added when the box is wider than 36: that is rule H-5.

Levelling legs by cabinet width, legs style.
Cabinet widthLegs
24 in4
36 in4
48 in6
Levelling legs by cabinet width, legs style.

The leg count is a hardware count only. The engine does not size the legs or choose a brand, so you choose the leg for the kick height you set.

Toe kick height and depth: what the sources say

The defaults are a 4 1/2 high and 3 deep toe kick. The fetched pages do not agree, which is why both are settings.

  • Best Online Cabinets, Kitchen Cabinet Standard Size Guideline: toe kick measures 4 1/2 in high.
  • Remodelista, Kitchen Cabinet Measurements: most toe kicks are 4 1/2 in.
  • Sebring Design Build, Kitchen Cabinet Sizes and Specifications Guide: standard height 3.5 in and standard depth 3 in, range 3 to 4.5 in high.
  • Erin Zubot Design, A Guide for Standard Kitchen Cabinet Dimensions: standard toe kicks are 4 in.

Two sources give 4 1/2 for the height, one gives 4 inches, and one gives 3 1/2 inches with a range of 3 to 4 1/2. Only one of them states a depth, 3 inches. So treat the defaults as a common choice, not a standard. Measure your own countertop, appliance and floor, and enter the height you need. The overall cabinet height is covered in standard base cabinet height.

Common mistakes

  • Cutting full-height sides for a separate base or legs. Those sides should be 30, not 34 1/2, or the cabinet comes out 4 1/2 too tall.
  • Cutting a notch and adding a base. The notch style already has the toe space, so a base under it doubles the kick.
  • Forgetting the cross members under a wide base. A 48 cabinet gets 3 here.
  • Setting the kick depth deeper than the cabinet allows. The cross member length is the side depth less the kick depth and two panel thicknesses, so it must stay above zero. The engine reports an error if it does not.
  • Leaving the kick height at the default when your countertop or floor needs another. It moves the box height, so the frame and the back change, and on a separate base or legs the side height too.

For the box itself see how to build a base cabinet box, and for how the frame changes things compare face frame and frameless, where frameless cabinets default to legs.

Questions people ask

What are the three ways to build a toe kick?

A notch cut in full-height sides, a separate base frame under a shorter box, or adjustable legs under a shorter box with a kick board across the front. The kick style is a setting on every base, tall and drawer base cabinet.

How tall should a toe kick be?

The fetched sources differ: two say 4 1/2 inches, one says 4 inches and one says 3 1/2 inches with a range of 3 to 4 1/2. The product defaults to 4 1/2 and lets you change it.

How many cross members does a separate base need?

The product uses the larger of two and the box width divided by 24 inches, rounded up, plus one (rule C-16). That count is a product assumption, so add more if your base spans a heavy load.

Do I cut a notch if I use legs?

No. With legs or a separate base the sides are shorter by the kick height and there is no notch. The notch applies only to the notch style, where the sides run the full cabinet height.

How many legs does a base cabinet need?

The default is four legs, with extra legs added when the box is wider than 36 inches (rule H-5). Both numbers are settings, and the tool lists the leg count as hardware.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool