Guide

How frameless cabinets are built

How frameless cabinets are sized: the 1.5 mm side and 3 mm pair reveals from a WoodWeb thread, door formulas, and a frameless 24 inch base cut list.

A frameless cabinet has no face frame: the box sides, top and bottom are the front of the cabinet, and the doors cover the box edge to edge. In the product rules the doors are sized from the cabinet width and height less reveals: 1.5 mm per side, 3 mm between a pair, 3 mm at the top and 0 at the bottom.

Those figures come from contributors on a WoodWeb knowledge base thread, where two others prefer 4 mm between doors. They are the metric defaults in the tool. The imperial defaults round them to 1/16 inch per side and 1/8 inch between doors.

Reveals and door sizes

Frameless door reveals. Source: WoodWeb Knowledge Base thread, read 2026-11-19. The tool's imperial defaults are rounded versions.
RevealMetric defaultImperial defaultWhat contributors state
Per cabinet side1.5 mm1/16 in1.5 mm on the sides (contributor B and the original poster)
Between a pair of doors3 mm1/8 in3 mm; contributor M calls it a safe distance for European hardware. Contributors J and O prefer 4 mm; B says 4 is too much
Between door and drawer, or stacked fronts3 mm1/8 in3 mm (contributor M and the original poster)
Top3 mm1/8 in3 mm (contributor B)
Bottom0 mm0 in0 mm (contributor B)
Frameless door reveals. Source: WoodWeb Knowledge Base thread, read 2026-11-19. The tool's imperial defaults are rounded versions.

Contributor M also cites a nominal AWI reveal of 3.2 mm (1/8 inch), with tolerances of 0.8 mm for Premium, 1.6 mm for Custom and 2.4 mm for Economy grade. That is a contributor's citation, not a figure we read in the standard. The thread is forum posts, so treat the numbers as shop practice and not as a standard.

D-8

H_fz = H_box - rev_top - rev_bot; W_fz = W - 2 x rev_side

D-11

pair: each W_door = (W_fz - gap_pair) / 2

For a 30 inch frameless base on the default kick, the box is 30 inches high and the pair of doors is 14 7/8 by 29 7/8 each (rule D-11). In metric the same rule on a 762 mm cabinet gives 378 mm each, which matches the thread's method of dividing the width by two and taking off 3 mm. A single 24 inch door is 23 7/8 by 29 7/8 (rule D-10). The calculator does this for any size: cabinet door size calculator.

Frameless cut list for a 24 inch base

A 24 wide, 34 1/2 high, 24 deep frameless base with a drawer over a door, at the default settings. There are no frame parts, and the kick is the legs style, so the sides are shorter than the cabinet by the kick height.

Frameless 24 inch base cut list from the engine. Inches.
PartQtyLengthWidthRule
Side23024C-5, C-6
Bottom122 9/1623 3/4C-8, C-9, C-10
Front stretcher122 9/164C-11
Rear stretcher122 9/164C-11
Back, 1/4123 5/1630C-12
Shelf122 7/1623 1/2C-14
Toe kick board1244 1/2C-16
Drawer front (drawer 1)123 7/85D-10
Drawer side (drawer 1)2223 23/32B-4, B-5, B-7
Drawer front/back (drawer 1)220 9/163 23/32B-3, B-7
Drawer bottom, 1/4 (drawer 1)121 1/1621 1/2B-8
Door (door 2)123 7/824 3/4D-10
Frameless 24 inch base cut list from the engine. Inches.
Frameless: the fronts cover the box and are separated by reveals. No frame shows.

The face frame version of the same cabinet is compared part by part in face frame and frameless. Toe kick choices are in toe kick styles, and overlay and reveal in door overlay and reveal.

What this page does not cover

  • Box construction and depth. Joinery, back methods and depth choices are in how to build a base cabinet box.
  • Edge banding. Which edges get banded is in edge banding allowance, not repeated here.
  • The 32 mm system. The tool does not produce hole patterns, and we did not research the system for this page.

Common mistakes

  • Sizing a frameless door from a frame opening. Frameless doors are sized from the whole cabinet width, less reveals.
  • Forgetting the toe kick when taking the door height. The front zone starts from the box height above the kick.
  • Using the imperial figures as exact. The metric reveals are the sourced ones, and the inch values are rounded.
  • Setting reveals tighter than your door maker can hold. One contributor notes that outsourced doors can come slightly oversized.

Questions people ask

What is the reveal between frameless cabinet doors?

A WoodWeb thread has contributors using 1.5 mm per side, 3 mm between a pair, 3 mm at the top and 0 mm at the bottom. One contributor group prefers 4 mm between doors. The tool defaults to the 3 mm figures.

What size should doors be for a 30 inch frameless base?

At the tool defaults a pair of doors on a 30 inch frameless base is 14 7/8 wide each and 29 7/8 high, from rule D-11. In metric, a 762 mm cabinet gives 378 mm each.

What is a frameless cabinet?

A cabinet with no face frame. The box sides, top and bottom form the front edge, and the doors and drawer fronts cover the box. In this tool that means no frame parts and doors sized from the cabinet width less reveals.

Are frameless cabinets easier to build?

The cut list has fewer parts because there is no face frame, and the tool defaults to legs for the toe kick. Whether that makes the build easier depends on your tools and joinery, which we do not rank.

Are frameless cabinets the same as full overlay?

In this tool the frameless doors cover the whole box, so they behave like full overlay. The sizing is different from a face frame overlay door, which adds an overlay to a frame opening. See the overlay guide for the three mounts side by side.

Sources

  1. WoodWeb Knowledge Base, Frameless Cabinet Door Dimensions and Tolerances (forum thread). Reveals 1.5 mm side, 3 mm between, 3 mm top, 0 bottom; one contributor prefers 4 mm. The URL in the product notes returned 404 on this date. Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool