Reference

Sizing inset cabinet doors

How big to make an inset cabinet door: the 1/16 inch gap per edge, the single and pair formulas, a worked 15 by 24 opening, and what inset does to drawer depth.

Leave 1/16 inch on every edge of an inset door. That is this tool's default, taken from the inchcalculator.com cabinet door calculator, which says inset doors "sit flush to the cabinet with a 1/16” gap around the edges." A 15 by 24 opening gives a door of 14 7/8 by 23 7/8 (rule D-5).

Contributors to a WoodWeb thread use somewhat larger gaps, from 5/64 to 3/32 inch, and one says 3/32 is already too much on painted doors. The gap is a setting, so enter what you will build.

The formulas

D-5

W_door = W_op - 2 x G_in; H_door = H_op - 2 x G_in

D-6

pair, no centre stile: each W_door = (W_op - 3 x G_in) / 2

D-7

drawer front = (W_op - 2 x G_in) x (H_op - 2 x G_in)

W_op and H_op are the face frame opening, measured between stiles and rails. The pair formula takes one gap at each edge and one between the leaves, which is three gaps. inchcalculator.com states the pair rule in words: subtract the clearance between the doors from the overall door size, then divide by 2.

Inset door sizes from the engine, at the default gap. Opening sizes in inches.
OpeningDoorQtySize (width x height)Rule
15 x 24Single door114 7/8 x 23 7/8D-5
30 x 24Pair of doors214 29/32 x 23 7/8 eachD-6
15 x 5 1/2Drawer front114 7/8 x 5 3/8D-7
Inset door sizes from the engine, at the default gap. Opening sizes in inches.
Inset fronts sit inside the frame openings, with a small gap on every edge.

What gap to leave

The sources we read do not agree on one figure, and we did not find a published standard. The calculator page gives 1/16 inch. WoodWeb contributors give 5/64 inch (about 2 mm), 3/32 inch (about 2.5 mm) and, for stain grade work, 2 mm, and one says 5/64 in summer and 3/32 in winter. One of them answered a question about 1/8 inch on painted doors by saying 3/32 is already too much. The table shows what each gap does to the same 15 by 24 opening.

The same 15 x 24 opening with different gaps. The 1/8 row is for comparison, not a sourced figure.
Gap per edgeSingle door
1/16 inch14 7/8 x 23 7/8
5/64 inch14 27/32 x 23 27/32
3/32 inch14 13/16 x 23 13/16
1/8 inch14 3/4 x 23 3/4
The same 15 x 24 opening with different gaps. The 1/8 row is for comparison, not a sourced figure.

Every 1/32 inch of gap takes 1/16 inch off the width and the height. Paint, humidity and the door maker's tolerance all use up some of that, so confirm the figure with whoever makes your doors.

Inset drawers and slide depth

B-5

D_clear = D_h + T_ff - (front thickness if inset); slide = longest length with L <= D_clear - c_rear

An inset front sits inside the frame, so it takes its thickness out of the depth available to the drawer box. In the 24 inch deep example the drawer side is 22 inches long with inset fronts and 22 with overlay, because slide lengths come in steps. On a shallower cabinet the step can fall to a shorter slide. See drawer box sizes for the full rules.

Do inset cabinets have a face frame?

The inset sizing rules in this tool apply to face frame cabinets, where the door sits in an opening framed by stiles and rails. The product rules we work from have no frameless inset mode, so for a frameless box see frameless cabinets. The width of the stiles sets the opening, see face frame dimensions. Overlay, partial and inset side by side are in cabinet door overlay and reveal.

Common mistakes

  • Measuring the cabinet, not the opening. Inset doors are sized from the frame opening, so measure between the stiles and rails.
  • Subtracting the gap once, not twice, for a single door. There is a gap on both edges.
  • Using the single formula for a pair. A pair has three gaps across the opening, not two.
  • Assuming the opening is square. Measure it at both ends and use the smaller figure.

Questions people ask

How much gap should I leave around inset cabinet doors?

The inchcalculator.com cabinet door calculator says inset doors sit with a 1/16 inch gap around the edges, and this tool defaults to that. WoodWeb contributors use 5/64 to 3/32 inch. The gap is a setting, so enter your own.

How do I size a pair of inset doors?

Subtract three gaps from the opening width and divide by two: one gap at each edge and one between the leaves. At 1/16 inch, a 30 inch opening gives two doors each 14 29/32 inches wide, from rule D-6.

Do inset cabinets have a face frame?

The inset rules in this tool are for face frame cabinets, where the door sits in a framed opening. The rules we use have no frameless inset mode, so we do not give sizes for one.

Can you add inset doors to existing cabinets?

We read nothing that tests this. The sizing is arithmetic: measure the frame opening at both ends, take the smaller figure and subtract the gap on every edge. Whether the frame is square enough is for you to judge.

Does an inset door change the drawer slide length?

It can. An inset front sits inside the frame and takes its thickness out of the depth available to the box, rule B-5. Slide lengths come in steps, so the chosen slide may or may not shorten.

Sources

  1. inchcalculator.com, Cabinet door calculator. 1/16 inch gap around inset doors; pair rule in words Read .
  2. WoodWeb Knowledge Base, Inset Cabinet Door Fitting and Tolerances (forum thread). Contributors use 5/64 to 3/32 inch, or 2 to 2.5 mm Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool