Reference

Face frame dimensions

There is no standard face frame width. See the 1 1/2 inch defaults, what woodworkers say, and how overhang changes carcass width and slide blocking.

There is no standard face frame width. The sources we read say so: a WoodWeb thread quotes a contributor saying there are "really no rules about face frame width" and another saying 1 1/2 inches is the most common, with 2 inches also widely used. This tool defaults every stile and rail to 1 1/2 inches and 3/4 inch thick. That is an assumption for you to confirm, not a standard.

The frame does not overhang the box by default (overhang 0). Any overhang narrows the carcass by twice that amount (rule C-1) and shrinks the slide blocking (rule F-8).

Widths: the tool's defaults against what contributors say

Face frame members: this tool's defaults and the figures contributors give in the WoodWeb thread Face Frame Width Issues (read 2026-11-19).
MemberTool defaultWhat contributors state
Stile (rule F-2)1 1/2 in1 1/2 in "most common"; one uses 2 in, another 1 3/4 in; one 1 1/4 in; metric: 32 mm end stiles, 50 mm centre stiles
Top rail1 1/2 inSame range; one contributor uses 1 1/4 in bottom and middle rails with 1 3/4 in stiles
Bottom rail1 1/2 inAs above
Middle rail and centre stile1 1/2 inOne contributor: 50 mm mid rails and mid stiles
Thickness3/4 inNot stated in what we read. Tool assumption
Face frame members: this tool's defaults and the figures contributors give in the WoodWeb thread Face Frame Width Issues (read 2026-11-19).

Contributors give reasons, not rules. One says 2 inch frames limit how far a concealed hinge can cover. Another attributes the popularity of 2 inches to simple cut-list arithmetic. One says the width varies by region. So pick the width for the look and the hinge you use, then enter it. If you plan doors on inset hinges, see inset cabinet doors, which also covers how frame width relates to the opening.

What the widths make in the cut list

For the 24 wide, 34 1/2 high face frame base with a drawer over a door, at the defaults, the frame stile is listed as 1 1/2 by 30 (2 pieces) and the top rail as 21 by 1 1/2. Rule F-2 sets the stile as S_ff by the box height, and F-3 sets each rail as the cabinet width less two stiles.

The frame: two stiles, a top rail, a middle rail and a bottom rail, with the opening for each front between them.

Widen the stile and the opening gets narrower, the rails get shorter and the doors change with them. The step by step build is in how to build a base cabinet box and the frame calculator is here.

Overhang and what it does to the box

C-1

W_box = W - 2 x ff_over (face frame)

F-8

B = S_ff - ff_over - T; blocking B thick each side of each side-mount drawer

The tool's overhang setting is how far the frame sticks out past each side of the box. The default is 0: the frame and the box are the same width. A positive value narrows the box and everything inside it, and leaves less of the stile to cover the panel edge. The values below are illustrations, not sourced figures.

The 24 inch face frame base with three overhang settings. Illustrative values.
Overhang per sideBox widthBottom lengthBlocking thickness B
0 (default)2422 9/1625/32
1/1623 7/822 7/1623/32
1/823 3/422 5/1621/32
The 24 inch face frame base with three overhang settings. Illustrative values.

If the overhang is large enough that B falls below zero, the carcass side would stand proud of the frame opening, and the engine reports an error. See face frame and frameless for how the two styles differ.

Common mistakes

  • Taking 1 1/2 inches as a standard. It is the tool's default and a common choice, nothing more.
  • Changing the stile width but not the overhang. B depends on both.
  • Forgetting that a wider stile narrows the door opening, and so the door.
  • Leaving the frame thickness at the default when your stock is another thickness. It sets slide depth for inset fronts.

Questions people ask

What are the standard dimensions of cabinet face frames?

We found no standard. A WoodWeb thread says 1 1/2 inches is most common and also that there are no rules on width, with 2 inches popular too. This tool defaults stiles and rails to 1 1/2 inches by 3/4 inch thick as an assumption to confirm.

How wide should cabinet face frame stiles be?

Contributors use 1 1/4, 1 1/2, 1 3/4 and 2 inches, or 32 and 50 mm. Choose for the look and your hinge, since one contributor notes 2 inch frames limit concealed hinge coverage. Enter your choice in the tool.

How far should a face frame overhang the cabinet box?

The tool defaults to 0, so frame and box are the same width. Any overhang narrows the box by twice its value under rule C-1. We could not source a typical scribing allowance, so we give none.

Does the face frame overhang change the cut list?

Yes. Box width is the cabinet width less two overhangs, so the bottom, stretchers and back change, and slide blocking is stile width less overhang less the panel thickness (rule F-8).

Do I need a wider frame for inset doors?

We read nothing that sets a width for inset. The frame width sets the opening, and the inset door is the opening less the gap on each edge, so the width you choose flows straight through to the door size.

Sources

  1. WoodWeb Knowledge Base, Face Frame Width Issues (forum thread). Contributor widths and the statement that there are no rules Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool