Reference

Toe kick dimensions

Toe kick height and depth as the sources we read state them, where they differ, and the parts to cut for a separate base under a 24 inch cabinet.

No source we read states a single standard toe kick. This tool defaults to 4 1/2 inches (114 mm) high and 3 inches (76 mm) deep, and treats both as settings you change. The fetched pages give 4 1/2 inches most often, with 4 inches and 3 1/2 inches also stated, and only one page gives a depth.

To build the kick as a separate base for a 24 inch cabinet, cut 2 rails 24 by 4 1/2 inches and 2 cross members 18 13/16 by 4 1/2 inches (rule C-16), and cut the sides 30 inches high instead of full height (rule C-3).

What the sources say about height and depth

The figures below are what each page states, read on 2026-11-19. None of them is a published standard, and where they differ we show both.

Toe kick figures as stated by each page we read.
SourceWhat it states
Best Online Cabinets, Kitchen Cabinet Standard Size Guidelinetoe kick measures 4 1/2 in high
Remodelista, Kitchen Cabinet Measurementsmost toe kicks are 4 1/2 in
Sebring Design Build, Kitchen Cabinet Sizes and Specifications Guidestandard height 3.5 in and standard depth 3 in, range 3 to 4.5 in high
Erin Zubot Design, A Guide for Standard Kitchen Cabinet Dimensionsstandard toe kicks are 4 in
WoodWeb Knowledge Base, Base Cabinet and Toe Kick Heights (forum thread)One contributor builds 4 1/2 in kicks after moving from 4 in; another uses around 4 1/2 in or 114 mm; a third uses 4 in. No contributor discusses depth.
Toe kick figures as stated by each page we read.

So the height is 4 1/2 inches in most of what we read, 4 inches or 3 1/2 in a minority, and the depth is 3 inches in the one page that gives it. The product takes 4 1/2 by 3 (114 by 76 mm in the metric defaults) as a starting point. Measure your own floor, appliance and countertop and enter what you need. For the overall cabinet height see standard base cabinet height.

Building the kick as a separate base

A separate base is a frame you build on the floor, level and fix, then set the cabinet box on. The box is shorter by the kick height, and the frame carries it. The parts for a 24 wide, 34 1/2 high, 24 deep face frame base at the default settings:

Sides and base parts for a 24 inch face frame base with a separate base, from the engine.
PartQtyLengthWidthRule
Side23023 1/4C-5, C-6
Base front/back rail2244 1/2C-16
Base cross member218 13/164 1/2C-16
Sides and base parts for a 24 inch face frame base with a separate base, from the engine.
The box sits on a frame of two rails and cross members. The front rail is set back from the box front by the kick depth.
C-3

H_side = H - kick for a separate base. Here 30.

C-16

Cross member = (D_side - kick_d - 2T) x kick_h = (23 1/4 - 3 - 1 7/16) x 4 1/2 = 18 13/16 x 4 1/2

The cross member count, the larger of two and the box width over 24 inches rounded up plus one, is a product assumption and not a sourced figure. Add more members if the base carries a heavy countertop. The kick board that closes the front is a separate piece in the other styles. Notch, legs and the full comparison are in toe kick styles, and the box itself is in how to build a base cabinet box.

Cabinets without a toe kick

Wall cabinets have no kick: the engine sets the kick to zero for them (rule C-2) and the sides are the full height. The tool does not build a base cabinet with no kick: it refuses a kick height of 0, because the kick board would have no height. If you want a base without a toe space, use a small kick height and edit the list, or build it by hand. The pages we read describe the kick as the recess for feet, and none says how to finish a base without one.

Common mistakes

  • Cutting full-height sides for a separate base. They should be 30 inches, not 34 1/2, or the cabinet stands 4 1/2 inches too tall.
  • Treating 4 1/2 by 3 as a rule. It is a common figure in the pages we read, not a standard.
  • Setting the kick deeper than the cabinet allows. The cross member length falls to zero, and the engine reports an error.

See the full parts list for a base in the base cabinet cut list.

Questions people ask

How tall is a toe kick?

The pages we read mostly say 4 1/2 inches, and others say 4 inches or 3 1/2 inches, in a range of 3 to 4 1/2. This tool defaults to 4 1/2 inches (114 mm) and lets you change it.

How deep is a toe kick?

Only one page we read states a depth, 3 inches. The tool defaults to 3 inches (76 mm). Measure the foot space you need, since depth is a setting and not a fixed standard.

What is the standard height of a kickboard?

We did not find a published standard. The fetched pages give 4 1/2 inches most often, so the tool starts there, and the kick board is cut as the box width by the kick height.

How do I build a separate toe kick base for cabinets?

Build a frame of a front rail and a back rail the width of the cabinet box, with cross members between them, each the kick height tall. The cabinet sides are then shorter by the kick height. Rule C-16 gives each part size.

Can a base cabinet have no toe kick?

Wall cabinets have none, but the tool refuses a kick height of 0 on a base, since the kick board would have no height. The sources we read do not describe how to build a base without one, so we give no sizes for it.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool