Reference

Plywood for cabinets

Plywood thickness for each cabinet part, why 3/4 inch plywood measures 23/32, and how a different sheet thickness changes every size on the cut list.

Most cabinet boxes in this tool are built from 23/32 inch plywood, which is what a sheet sold as 3/4 inch measures. The one page we read that lists actual thicknesses says a 3/4 inch sheet is 23/32 inch, a 1/2 inch sheet is 15/32 inch and a 1/4 inch sheet is 7/32 inch, and says to measure with a caliper. The tool defaults to 23/32 inch (18 mm) for boxes, 1/4 for backs, 1/2 for drawer sides and 1/4 for drawer bottoms.

Whether 1/2 inch is strong enough for a box is a judgement the sources we could read do not settle, and we did not read a strength test. What we can show is what changes in the cut list: every width and depth that depends on the panel thickness moves.

Thickness by part: the tool's defaults

These are the starting values for a new cabinet. Each is a setting you can change, and the printed sizes follow the change.

Panel thickness by part, from the product defaults. Imperial and metric defaults are separate settings.
PartSettingImperial defaultMetric defaultStatus
Sides, bottom, top, shelves, stretchersT23/3218Sourced: 3/4 in plywood is typically 23/32 in (18 mm)
BackT_back1/46Tool assumption
Drawer sides, front and backT_ds1/212From the Popular Woodworking example, which uses 1/2 in sides
Drawer bottomT_db1/46Tool assumption
Panel thickness by part, from the product defaults. Imperial and metric defaults are separate settings.

Notice that the 1/2 and 1/4 defaults are round numbers. If you buy sheets sold as 1/2 or 1/4 inch plywood, the page we read gives 15/32 and 7/32 for them, so enter what you measure. The tool does not convert nominal sizes for you.

Nominal against actual

Actual thickness of plywood sold by nominal size, as stated by inchcalculator.com (read 2026-11-19).
Sold asActual thickness stated
3/4 inch23/32 inch
1/2 inch15/32 inch
1/4 inch7/32 inch
Actual thickness of plywood sold by nominal size, as stated by inchcalculator.com (read 2026-11-19).

The same page says plywood is often 1/32 inch thinner than its nominal size and that a caliper is the only accurate way to know. We read one source, so listings from other makers may differ. That answers the common question about 15/32: on that page it is the actual thickness of a sheet sold as 1/2 inch. We did not read anything on 5/8 inch sheets, so we say nothing about them here.

What the thickness changes in the cut list

C-7

W_in = W_box - 2 x T; bottom length L_h = W_in (butt joint)

The same 24 wide, 34 1/2 high, 24 deep face frame base is cut below with three carcass thicknesses. The first is the default. The second types 3/4 inch, as if the sheet were exactly nominal. The third is 15/32 inch for a sheet sold as 1/2 inch.

One 24 inch face frame base cut with three carcass thicknesses. Lengths and widths in inches.
PartT = 23/32T = 3/4T = 15/32
Side (length x width)34 1/2 x 23 1/434 1/2 x 23 1/434 1/2 x 23 1/4
Bottom22 9/16 x 2322 1/2 x 2323 1/16 x 23
Back23 5/16 x 3023 1/4 x 3023 13/16 x 30
Shelf22 7/16 x 22 3/422 3/8 x 22 3/422 15/16 x 22 3/4
One 24 inch face frame base cut with three carcass thicknesses. Lengths and widths in inches.

The bottom is 22 9/16 at the default and 22 1/2 at 3/4, a difference of 1/16 inch. Thinner panels make interior parts longer, because there is more room between the sides. Side height does not change, so the doors, face frame and kick are untouched. For the full derivation see how to build a base cabinet box.

Thickness also changes the sheet count a little, since parts come out of different stock groups: panels of different real thickness never share a sheet in the layout. See sheet layout and kerf and the plywood calculator.

1/2 inch or 3/4 inch for boxes

Forums are split on this, and we are not going to name a winner. What the tool can tell you is the arithmetic: set T to what you measured and the cut list follows, as the table shows. Joinery matters too. A dado or rabbet depth must stay under the panel thickness, and the engine refuses a dado deeper than T. Check your joint at the thickness you will actually use.

Plywood, melamine, MDF and grade

Each material role (carcass, back, drawer side, door, frame) has its own material name and a grain flag in the tool, so you can list melamine or MDF for the carcass. Grained sheet parts must follow the sheet length, and ungrained ones may rotate. We have no data on plywood grades, species or brands, so this page gives no advice on them.

Common mistakes

  • Typing 3/4 when the sheet measures 23/32. The bottom and shelf come out too short by twice the difference.
  • Typing 1/2 for a sheet that measures 15/32. Same error, other direction.
  • Mixing thicknesses on one cabinet without changing the matching setting. Back, drawer sides and drawer bottoms each have their own.
  • Treating a nominal size as exact. The only figure that counts is the one on your calipers.

Questions people ask

What is the standard thickness of plywood for cabinets?

We found no published standard. The tool defaults to 23/32 inch (18 mm) for boxes, which is what a sheet sold as 3/4 inch typically measures, with 1/4 inch backs and 1/2 inch drawer sides. Measure your own sheet and enter it.

Why is 3/4 plywood actually 23/32?

The page we read says a 3/4 inch sheet is actually 23/32 inch thick and that plywood is often 1/32 inch under its nominal size. It does not explain why, and it says a caliper is the only accurate check, so measure each batch.

Are cabinets 1/2 or 3/4 inch?

Both are used and forum opinion is split. In this tool the carcass thickness is one setting, so you can cut the same cabinet either way and see how each panel width changes, as the table above shows.

Is 15/32 plywood the same as 1/2 inch?

On the page we read, 15/32 inch is the actual thickness of a sheet sold as 1/2 inch. We did not read about 5/8 inch sheets, so we cannot compare them.

What changes in the cut list if my plywood is thinner?

Interior widths and depths grow, because the bottom, top and shelves sit between sides that are thinner. Side height, face frame and door sizes stay the same. Enter the measured thickness so each part follows.

Sources

  1. inchcalculator.com, Actual plywood thickness and size. 3/4 is 23/32, 1/2 is 15/32, 1/4 is 7/32; measure with a caliper Read .

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool