Cut list guide

Kitchen unit cutting list

Cutting list for a 600 mm kitchen base unit carcass in 18 mm board, with widths from 300 to 1000 mm, plinth and back sizes. Sizes are worked examples.

A 600 mm frameless base unit, 870 mm high and 560 mm deep, cuts from 18 mm board into the parts in the table below. Its sides are 756 mm by 560 mm and its bottom is 564 mm long, because the bottom sits between two 18 mm sides.

The sizes 870 high and 560 deep are examples. We did not read a source that states a standard carcass size in millimetres, so change them to match your own range and the tool recalculates.

Cutting list for a 600 mm base unit carcass

This is the tool in metric with the frameless defaults: 18 mm board for the carcass, a 6 mm back, a 114 mm plinth and a 3 mm saw kerf. Every size below is the cut size, in millimetres, before any edge banding thickness is added or removed. Thicker or thinner board changes the numbers: set the real thickness of your sheet in the tool.

Cutting list for one 600 mm frameless base unit, every part line, with the rule that sized it. Sizes in millimetres.
PartQtyLengthWidthRule
Side2756560C-5, C-6
Bottom1564554C-8, C-9, C-10
Front stretcher1564100C-11
Rear stretcher1564100C-11
Back, 61582756C-12
Shelf1561548C-14
Toe kick board1600114C-16
Drawer front (drawer 1)1597150D-10
Drawer side (drawer 1)2500118B-4, B-5, B-7
Drawer front/back (drawer 1)2514.5118B-3, B-7
Drawer bottom, 6 (drawer 1)1526.5488B-8
Door (door 2)1597600D-10
Cutting list for one 600 mm frameless base unit, every part line, with the rule that sized it. Sizes in millimetres.
Front of the 600 mm example unit. The drawn fronts are the tool's default arrangement.

The list has a 114 mm high plinth board (rule C-16), and the sides are shorter than the unit by that height: 756 mm against 870 mm. See toe kick styles for the three ways to do it.

Unit widths from 300 to 1000 mm

These eight widths are the tool's example widths. We did not fetch a source that states a width series for kitchen units, so check the ranges you buy against your supplier. Width changes the bottom, the stretchers, the back and the doors. It does not change side size.

Same 870 by 560 frameless unit at eight widths. Bottom length, first door size and hinges as the tool calculates them. Millimetres.
Width (mm)Bottom lengthDoor (length x width)HingesParts
300264297 x 600215
400364397 x 600215
450414447 x 600215
500464497 x 600215
600564597 x 600215
800764397 x 600416
900864447 x 600416
1000964497 x 600416
Same 870 by 560 frameless unit at eight widths. Bottom length, first door size and hinges as the tool calculates them. Millimetres.

One unit on a sheet

The sheet is 4 by 8 feet by default. A UK or metric supplier may cut 2440 by 1220 mm; set your own sheet size in the tool and the layout follows. The diagram shows the main board group of the 600 mm unit.

PLYWOODSide 129 3/4 x 22 1/16Side 229 3/4 x 22 1/16Door23 5/8 x 23 1/2Toe kick boardDrawer frontBottom22 3/16 x 21 13/16Front stretcherRear stretcherShelf22 1/16 x 21 9/16
Main Plywood group of one 600 mm unit on the default sheet. Grain runs along the long edge.

Common mistakes

  • Taking the sheet as 18 mm when it is 17.5 or 18.5. Measure and enter the real thickness.
  • Cutting the bottom the full width of the unit. It sits between the sides, so it is 564 mm, not 600 mm.
  • Forgetting the back. It is a separate, thinner board.
  • Planning a 560 mm deep unit without a worktop overhang and a wall box depth in mind.

The same engine runs imperial on the kitchen cabinet cut list page, with different units, defaults and numbers. For door sizes in millimetres use the cabinet door size calculator, and for the construction rules see face frame against frameless.

Questions people ask

What is the cutting list for a 600 mm base unit carcass?

It is two sides, a bottom, two stretchers, a thin back, a shelf and fronts, sized from your board thickness. The table above gives every part for a 600 by 870 by 560 mm example in 18 mm board.

What are standard kitchen carcass sizes in mm?

We did not read a source stating them, so this page does not claim a standard. The 600 mm width, 870 mm height and 560 mm depth are examples; enter your supplier's sizes in the tool and it recalculates every part.

How do I make a cutting list for kitchen cupboards?

List one cabinet at a time: size the sides first, then the bottom between them, the stretchers, the back, then doors and drawer fronts. Group parts by board thickness. The tool does this for each cabinet and totals the sheets.

Does the tool work with 18 mm board?

Yes. The metric defaults use 18 mm for the carcass and 6 mm for the back. If your board measures differently, enter its real thickness and every part that depends on it changes.

What plinth height should I use?

The tool defaults to a 114 mm plinth. We did not fetch a source for a standard figure in millimetres, so set the height to match your legs or plinth system.

Run your own cabinet

The numbers in this article come from the same engine as the tool. Free for one cabinet, no account.

Open the cut list tool