Sink base cabinet cut lists by width
Parts, sheet counts and yield for every standard sink base cabinet width from 30 to 36 inches, face frame and frameless, from the cut list rules.
A standard sink base cabinet comes in 3 widths from 30 to 36 inches in the sources we read. As a face frame cabinet it runs from 15 to 15 parts, and its main plywood from 1 to 1 sheet per cabinet at the tool's defaults (34 1/2 high, 24 deep).
Every width, both styles
| Width | Parts (face frame) | Parts (frameless) | Bottom length | Hinges | Sheets FF | Sheets FL | Yield FF |
|---|---|---|---|---|---|---|---|
| 30 in | 15 | 10 | 28 9/16 | 4 | 1 | 1 | 74% |
| 33 in | 15 | 10 | 31 9/16 | 4 | 1 | 1 | 78% |
| 36 in | 15 | 10 | 34 9/16 | 4 | 1 | 1 | 82% |
The tool switches from one door to a pair at 30 inches, because a door wider than 24 inches draws a warning. Widths come from the sources, which differ on the extremes: Bob Vila gives 30 inches for a single sink and 36 for a double; Hunker gives 30, 33 and 36.
Each width, part by part
30 inch sink base cabinet
Face frame: 15 parts, 4 hinges, bottom 28 9/16 long, side 23 1/4 deep. Frameless: 10 parts, side 24 deep. Main plywood: 1 sheet face frame at 74%, 1 frameless at 73%.
| Part | Qty | Length | Width | Rule |
|---|---|---|---|---|
| Bottom | 1 | 28 9/16 | 23 | C-8, C-9, C-10 |
| Stretcher | 2 | 28 9/16 | 4 | C-11 |
| Back, 1/4 | 1 | 29 5/16 | 30 | C-12 |
| Toe kick board | 1 | 30 | 4 1/2 | C-16 |
| Frame rail (top) | 1 | 27 | 1 1/2 | F-3, F-4 |
| Frame rail (middle) | 1 | 27 | 1 1/2 | F-3, F-4 |
| Frame rail (bottom) | 1 | 27 | 1 1/2 | F-3, F-4 |
| False front (false front 1) | 1 | 28 | 6 | D-4 |
| Door (door 2) | 2 | 13 15/16 | 21 1/2 | D-2 |
33 inch sink base cabinet
Face frame: 15 parts, 4 hinges, bottom 31 9/16 long, side 23 1/4 deep. Frameless: 10 parts, side 24 deep. Main plywood: 1 sheet face frame at 78%, 1 frameless at 77%.
| Part | Qty | Length | Width | Rule |
|---|---|---|---|---|
| Bottom | 1 | 31 9/16 | 23 | C-8, C-9, C-10 |
| Stretcher | 2 | 31 9/16 | 4 | C-11 |
| Back, 1/4 | 1 | 32 5/16 | 30 | C-12 |
| Toe kick board | 1 | 33 | 4 1/2 | C-16 |
| Frame rail (top) | 1 | 30 | 1 1/2 | F-3, F-4 |
| Frame rail (middle) | 1 | 30 | 1 1/2 | F-3, F-4 |
| Frame rail (bottom) | 1 | 30 | 1 1/2 | F-3, F-4 |
| False front (false front 1) | 1 | 31 | 6 | D-4 |
| Door (door 2) | 2 | 15 7/16 | 21 1/2 | D-2 |
36 inch sink base cabinet
Face frame: 15 parts, 4 hinges, bottom 34 9/16 long, side 23 1/4 deep. Frameless: 10 parts, side 24 deep. Main plywood: 1 sheet face frame at 82%, 1 frameless at 82%.
| Part | Qty | Length | Width | Rule |
|---|---|---|---|---|
| Bottom | 1 | 34 9/16 | 23 | C-8, C-9, C-10 |
| Stretcher | 2 | 34 9/16 | 4 | C-11 |
| Back, 1/4 | 1 | 35 5/16 | 30 | C-12 |
| Toe kick board | 1 | 36 | 4 1/2 | C-16 |
| Frame rail (top) | 1 | 33 | 1 1/2 | F-3, F-4 |
| Frame rail (middle) | 1 | 33 | 1 1/2 | F-3, F-4 |
| Frame rail (bottom) | 1 | 33 | 1 1/2 | F-3, F-4 |
| False front (false front 1) | 1 | 34 | 6 | D-4 |
| Door (door 2) | 2 | 16 15/16 | 21 1/2 | D-2 |
What is particular to a sink base cabinet
A sink base has no drawer box. The drawer position is a false front, a front panel with no box behind it, so the slide and box parts are absent and the 33 inch version has 15 parts against 21 for a 30 inch base. The top is always two stretchers, and the front one is marked install on edge so the sink can drop in. The notes the tool adds are: Notch 4 1/2 x 3 at the front bottom corner of each side. Front stretcher: install on edge. Plumbing cut-outs in the back are made on site. Plumbing cut-outs are made on site. The frameless version is 10 parts.
Sheets in the table are for one cabinet alone. In a project the cabinets share sheets, so see how many sheets of plywood a kitchen needs and the plywood calculator for cabinets.
Questions people ask
Which widths does a standard sink base cabinet come in?
Bob Vila gives 30 inches for a single sink and 36 for a double; Hunker gives 30, 33 and 36. The table on this page covers 30, 33, 36 inches.
Does the cut list change much between widths?
The sides, back height and toe kick do not change with width. The bottom, stretchers, back width, shelves, face frame rails and doors do. The table shows the parts count and the main plywood sheets at each width.
Are these sizes a code or standard?
They are sizes reported by retail and editorial pages we read, not a published standard. Shops build to any size, and the tool takes any size you enter.